Model WFG320M0MS0
Customer reported no heat. Found igniter receiving 120VAC but not glowing. Replaced igniter and tested. Dryer heating properly.
Whirlpool repair
Whirlpool Range & Oven Repair
Fast, professional Whirlpool range repair from technicians who fix Whirlpool ranges frequently. Same or next business day on most calls.
- Factory-authorized Whirlpool service
- Upfront Appliance Blue Book pricing
- Stocked vans, so many repairs are done in one visit
- 10-year parts warranty, 60-day labor warranty*
- 30Whirlpool range repairs in our records
- 5.0average customer rating
Factory-authorized
Why factory-authorized Whirlpool service matters
- Factory-trained techniciansOur technicians are trained by Whirlpool and work on Whirlpool appliances frequently.
- Genuine Whirlpool parts, fastWe get genuine manufacturer parts directly, so the right part arrives faster.
- A direct line to WhirlpoolOur technicians can reach the manufacturer's own technical and engineering support teams, so the tough problems get solved faster and done right.
What we fix most on Whirlpool ranges
- Bake or broil igniter
- Surface burner or spark switch
- Control board
- Temperature sensor
- Bake or broil element
- Gas valve or regulator
Counted from our technicians' notes on 30 Whirlpool range service calls.
Gas oven slow to heat, or not heating
Whirlpool gas ranges light the bake and broil burners with a hot-surface igniter. As that igniter weakens, the oven takes longer and longer to light, and eventually it won't light at all. Replacing the igniter, a gas valve or a regulator is technician work, not a DIY job.
Electric oven stays cold
Look at the bake element. One that has burned through will show a blister or a break you can see. When the elements look fine, the trouble may be the temperature sensor, the wiring or the control board.
Burners that click and won't catch
Most of the time it's something simple. A burner cap isn't sitting flat on its base, a cap got put on the wrong burner, the burner ports are wet or clogged, or water got into the knob switches during cleaning. After a power outage, some models also lock the cooktop and show Locked until you hold the lock key for three seconds. When none of that is it, the spark switch, spark module or igniter needs checking.
Oven running hot, cold, or showing an F code
An oven that runs off temperature, or throws an F3 code, typically traces back to the temperature sensor or its wiring, and now and then the control. Range codes vary a lot from model to model. The ones below are confirmed on Whirlpool's own support pages.
| Code | What it usually means |
|---|---|
| F3 E0 | A fault in the oven temperature sensor, its wiring, or the control board it reports to |
| F3 E2 | Trouble with the oven temperature sensor (or the warming drawer sensor, if there is one) or its wiring |
| F9-1 | Door lock switch, the latch itself or related wiring, frequently noticed around self-clean |
For any of the three, cut power at the breaker for a full minute. Once it's back on, give the oven another minute and see if the code reappears. A code that comes back means the part needs testing.
Cooktop checks worth doing first
- Reseat each burner cap so the pins line up and it sits flush.
- Give wet burners and knob switches time to dry. A hair dryer on cool speeds that up.
- Use a straight pin, not a toothpick, on plugged ports, and be careful not to widen them.
- Check for a tripped breaker, and look for Locked on the display.
The model tag is on the oven frame or the storage drawer frame. Open either one and look.
Recent Whirlpool range repairs
Model WFES5030RZ0
Customer stated oven racks hard to pull out. Found case lip protruding and adjusted. Racks slide properly now.
“I was impressed. M & H Appliance locally here, where I bought my Whirlpool Range, made the excuse that those ranges are known to have the problem I had where the racks were hard to slide in and out and so it was end of story with them. I knew two other people with Whirlpool ranges and their racks slid easily in their ovens. So I contacted the manufacturer directly who put me in contact with Omega Force Appliance. Brandon could see the problem right away and with a simple adjustment on the flange that encased the opening, problem resolved!”
Tom W.
Model WFG505M0BS2
Unit slow to heat. Found weak igniter. Replaced and tested. Unit operating properly.
Model GW399LXUS06
Customer complaint of long preheat, replaced bad bake igniter, and unit heats properly now.
Model WSES5030SZ0
Replaced control board for pump running continuously and calibrated and verified proper washer operation
Model WFE505W0JS0
Replaced oven main board; broil element cycling properly ? oven in good order.
“He was very knowledgeable and got my issue fixed on time.”
Odell K.
Model MGT8775XS01
Repaired control board and replaced upper bake igniter, tested, upper oven heating properly.
“Mark was phenomenal. Best service technician we’ve ever had, period. Courteous, knowledgeable and went far above and beyond what we expected to repair our oven. We will never use anyone other than Omega in the future.”
Bart W.
Model SF367LXSB0
Replaced spark module board. Tested and bake and broil now heat. Oven preheated and cycling temperatures are correct. Range is working good.
“Called the number at 6:30 at night and got an appointment for the next day. Delton was great. He identified the problem with our stove and found an alternative part (we have a year old stove) that he thought would work. He installed the part the next day. His repair allowed us to not replace the stove and saved us money. Professional and trust worthy.”
John P.
Model WFE535S0JZ
I accessed the oven control relay board, removed it. Installed the new relay board, and plugged the range in. The random heating cycling has stopped, the relays have dropped popping and cracking.
“Arron was very efficient and knowledgeable, very nice personally also”
James D.
Model WGE745C0FS
Upon arrival, customer states that knob just spins and doesnt engage the switch. Replace knob with part provided and tested. Machine seems to be working properly now.
“Excellent service, friendly and prompt”
Molly L.
Model WFG515S0EW1
Returned removed the old igniter and installed new igniter, cycled and tested the oven starts and is operating as it should be.
“Excellent service. I loved the ability to get a service call that was convenient for me and quickly. After diagnosing, the repair parts arrived in short order and everything is up and running as it should again. Brandon also gave me some pointers on how to lengthen the life of the part that had to be replaced. He was very courteous and professional and neat.”
John K.
Model GR445LXMS
Returned with the part, removed the old one and installed the new one. Cycled and tested made sure the oven came on and worked on bake
“Brandon is a great tech and a true professional. He went out of his way to complete the job(oven repair) a day early, something you don’t see often anymore. We appreciate the service.”
Greg K.
Model WFE320M0JW3
Customer state unit not heating fully, confirmed oven cycling 50 degrees below set point. Replaced control board and temp sensor and retested unit now heating within spec.
Model WFG320MCBS3
The customer complained that the oven would not turn on at all. I informed them that the igniter had failed and, in order to resolve the issue, a new igniter was needed. After installing the new one, the oven turned on fast and heated up properly.
“My brother highly recommended them. Making the appointment was fast and very friendly service. Tech came and corrected the problem with my oven very quickly I highly recommend this company and would call them again if needed”
Tamara H.
Model WEE510S0FS2
Customer complaint is, problem with the temp control - ERROR CODE F6 E1 on electric range and the front door panel popped off. Customer said it got really hot in they smelled a burning electrical smell. Inspected and tested. Temperature sensor tested good at 1074 ohms. Found the bake relay has failed and is sticking and the front glass panel is falling off. Installed new board and front glass panel and tested. Range is now fixed.
“Professional and courteous”
David P.
Model WFE540H0ES0
The bake element was bad. Today we replaced the bake element and tested the oven. The bake element is working good now.
“Friendly, efficient and got job done in a timely manner!! Have my oven working for Thanksgiving!!”
Ginger W.
Model RF352BXGQ0
There is 3 different E2 codes; one is the board(which is most likely). Next is the thermostat. Checked that ohms out perfectly and checked average temp and is right on. Next is the self clean lock. Put unit in self clean and it locked properly no errors. Everything is testing properly. Checked the control board for any visual damage nothing visible. Customer is going to keep an eye on it and let us know
“Adam - Very professional and experienced. Great communication with honest answers”
Bob C.
Model WFG505M0BS2
The door handle was not loose. The part that is loose is the glued on metal frame around the outside of the glass. I advised the customer its not covered. The light bulb was broken off in the socket. I got the broken piece out and installed the new bulb the customer had. The customer said hot air is escaping from the door. The door seal is good and the door shuts good. I cleaned around the door seal and made sure the oven is working.
“Good service keep up the good work.”
Ahmed O.
Model WGG755S0BS01
Oven automatically comes on when you plug in the range. Found a shorted bake ignitor. Told customer that it looks like it needs a new ignitor, and if it didnt fix it, no charge for the ignitor. It didnt fix it. Then found a bad relay on the board (k4). Quoted for board repair. Soldered new relay on the board. Works great now.
“Nate was very polite and helpful. He solved the problem and saved us having to buy a new appliance!”
Eric G.
Model GS440LEMQ2
Customer complaint is, gas leak on the tube in the oven where the gas connectes to the regulator maybe igniter. Customer had gas turned off when I got here. Inspected and tested. Turned gas on and inspected valve and connectors with liquid leak detector and could not find any leaks. I tested burners and preheated oven to 350F and watched it cycle and everything is working great. I cant find a leak or anything wrong with this range.
“He checked what he could and didn’t find anything. Was very helpful and courteous. Thank you”
Kathy D.
Model WEG730H0DS0
I verified the back left burner igniter was broken. I removed the top then replaced the igniter. I tested all the burners and now all of them work perfectly.
“Great service! Able to come with the part needed and get it fixed in less than 30 minutes. Right on time for the scheduled window.”
Jessica B.
Model AGG222VDW0
Oven not heating. Found a bad bake ignitor.Got it fixed with flat ignitor. Heats great now.
“Very pleasant and prompt service. Completed job and added discount.”
Eileen B.
Model WFG525S0HZ0
Some of the display segments are going out. I verified the part that was sent was the correct part. I replaced the main board and verified its working.
“Fast and professional”
Philip L.
Model WFG520S0AS1
Wont bake. Failed DSI board and harness. I inspected it and it started to work after I re-assembled it. I quoted harness and board.
What Whirlpool range owners say
Rated 5.0 out of 5 stars by 30 Whirlpool range repair customers“Mark was phenomenal. Best service technician we’ve ever had, period. Courteous, knowledgeable and went far above and beyond what we expected to repair our oven. We will never use anyone other than Omega in the future.”
“Called the number at 6:30 at night and got an appointment for the next day. Delton was great. He identified the problem with our stove and found an alternative part (we have a year old stove) that he thought would work. He installed the part the next day. His repair allowed us to not replace the stove and saved us money. Professional and trust worthy.”
“Arron was very efficient and knowledgeable, very nice personally also”
“Excellent service. I loved the ability to get a service call that was convenient for me and quickly. After diagnosing, the repair parts arrived in short order and everything is up and running as it should again. Brandon also gave me some pointers on how to lengthen the life of the part that had to be replaced. He was very courteous and professional and neat.”
“Brandon is a great tech and a true professional. He went out of his way to complete the job(oven repair) a day early, something you don’t see often anymore. We appreciate the service.”
“My brother highly recommended them. Making the appointment was fast and very friendly service. Tech came and corrected the problem with my oven very quickly I highly recommend this company and would call them again if needed”
“Friendly, efficient and got job done in a timely manner!! Have my oven working for Thanksgiving!!”
“Adam - Very professional and experienced. Great communication with honest answers”
“Nate was very polite and helpful. He solved the problem and saved us having to buy a new appliance!”
“He checked what he could and didn’t find anything. Was very helpful and courteous. Thank you”
“Great service! Able to come with the part needed and get it fixed in less than 30 minutes. Right on time for the scheduled window.”
“Very pleasant and prompt service. Completed job and added discount.”
Whirlpool range repair FAQ
What goes wrong most often on Whirlpool ranges?
In our technicians' notes on 30 Whirlpool range service calls, the repairs that come up most involve the bake or broil igniter, surface burner or spark switch and control board. The list near the top of this page shows the rest.
How many Whirlpool ranges have you repaired?
30 Whirlpool range repairs are in our service records so far, and customers rated those visits 5.0 out of 5 stars.
Why does my Whirlpool stove keep clicking?
When it clicks even though every knob is off, water has probably gotten into the knob switches after a spill or a wipe-down. Time fixes that. To hurry it along, take the knobs off and point a hair dryer, set to cool, at the bare shafts. Clicking without lighting is a different problem, and the cause tends to be a burner cap that isn't flat or is sitting on the wrong burner. Still happening once everything is dry and seated? The spark switch or module needs a look.
What does F3 E0 mean on a Whirlpool oven?
Whirlpool points to three possible culprits, which are the wiring, the oven temperature sensor and the control. Try a power reset first. Leave the range breaker off for one minute, then switch it on and keep an eye on the oven for a minute more. A code that comes back means the sensor and its wiring need testing. The sensor is the most common fix, but not the only one.
Why won't my Whirlpool burners light after a power outage?
After an outage, or after the range has been unplugged, some Whirlpool models lock the cooktop and show Locked. Press the lock key and keep holding for about three seconds, until its indicator light turns off. On a brand-new range, light one burner briefly at first so air can purge out of the gas line. Burners that still won't light need service.
Where is the model number on a Whirlpool stove?
Open the oven door and check the frame, or pull the storage drawer all the way out and look on the frame behind it. Write down both the model and serial numbers or snap a photo. The model number decides which igniter, element, sensor or control board fits your range.
How much does Whirlpool range repair cost?
The trip and diagnostic fee starts at $129. Your technician quotes the repair upfront using the Appliance Blue Book, before any work begins, so you can decide with no surprises.
Are you a factory-authorized Whirlpool service provider?
Yes. Omega Force Appliance Repair is a factory-authorized Whirlpool service provider.
Is the repair guaranteed?
Repairs you pay us for directly come with a 10-year warranty on parts and a 60-day labor warranty. When a manufacturer, home warranty company or other third party pays for the repair, that company's warranty applies instead.
Omega Force Appliance Repair is a factory-authorized Whirlpool service provider.