We serviced a
MAYTAG WASHER FRONT LOA
Model MHW6000XW1
Near Minneapolis, Minnesota 55446
Phillip
Job Details:
05/17/2022
The drain pump was full of gunk. I cleaned the drain pump and glued the top vent in place. I also fixed the control panel that was loose. F9e1
We serviced a
ELECTROLUX DISHWASHER
Model EIDW6305GS1
Near Hopkins, Minnesota 55305
Phillip
Job Details:
05/17/2022
The dishwasher had the leak code. I pulled it out and found water in the pan. I did find water leaking from the water inlet seal. I put glue around the seal and made sure the nut was tight. So far no leaking .
We serviced a
GE DISHWASHER
Model GDT645SYN4FS
Near Otsego, Minnesota 55362
Seth
Job Details:
05/17/2022
Stops mid-cycle wont drain. The customer custom installed the dishwasher. It is not appropriate for the application. He will correct the installation.
We serviced a
MAYTAG WASHER TOP LOAD
Model MVWC450XW4
Near Minneapolis, Minnesota 55419
Nate
Job Details:
05/17/2022
Washer leaking water and not advancing. A squirrel that was living in their kitchen chewed through the drain line. Quoted customer for new drain line. C1 labor. P; ordrd 1 W11244231 (Drain line)
We serviced a
MAYTAG WASHER FRONT LOA
Model MHW5500FW1
Near Elk River, Minnesota 55330
Matt
Job Details:
05/17/2022
"Customer complaint is, NOT DRAINING, CLEANED TRAP AND REPLACED PUMP AND STILL WONT DRAIN. Inspected and tested. Drain pump is continuously running. Checked air trap and its clear. The pressure sensor has failed. Installed new pressure sensor and tested. Washer is working great. Washer is now fixed. ; used 1 WPW10448876 (PRESSURE SENSOR) from stock"
We serviced a
GE REFRIGERATOR
Model CYE22TP2MHS1
Near Hopkins, Minnesota 55343
Phillip
Job Details:
05/17/2022
The customer had the fresh food set to 34 but temps were around 39-41. There was no related faults and everything was working as it should. There was a firmware update that addressed some of the issues. I ran the firmware update. I advised the customer to give it 48 hours to get back to temps. I set the fresh food temp to 37.
We serviced a
GE REFRIGERATOR
Model CFE28TSHESS
Near Inver Grove Heights, Minnesota 55077
Delton
Job Details:
05/17/2022
Found that evaporator fan in fresh food section is bad and barely spins. Customer approved estimate. Replaced fan and did software update. Tested and refrigerator is cooling and working good.; used 1 WR60X26866 (FRESH FOOD FAN) from stock
We serviced a
MAYTAG WASHER FRONT LOA
Model MHWE550WW01
Near Minneapolis, Minnesota 55410
Nate
Job Details:
05/17/2022
Sounds like an airplane taking off when it spins. Tub is loose too. Has a bad bearing. . ; O-emld tckt
We serviced a
WHIRLPOOL REFRIGERATOR
Model ET20NKXDN00
Near Columbia Heights, Minnesota 55421
Phillip
Job Details:
05/17/2022
The customers were concerned that the freezer temperature was getting up in the 20s at times. As advised a customer it was probably happening during the defrost and theres nothing to worry about. I did find that the freezer door was not sealing tight all the way and that was letting moisture into the freezer. I adjusted the freezer door hinges so the door does not rub and shuts better and I put some grease on the freezer door gasket.
We serviced a
KENMORE DRYER- GAS
Model 11070172002
Near Minneapolis, Minnesota 55423
Adam
Job Details:
05/17/2022
"Unit wasnt Venting out of back of dryer. Removed back cover. Found the blower wheel was loose and an extreme amount of lent and debris in vent. This is probably the reason for the wheel coming loose. Re-tightened the blower wheel. And tested unit. Found the high limit thermostat was popped. Replaced thermostat and tested unit. Reassembled dryer and now operating properly.; used 1 DUCT-90 (DE904 90 ELBOW), and 1 WP3387134 (THERMOSTAT) from stock"
We serviced a
KENMORE REFRIGERATOR
Model 79571013010
Near Eagan, Minnesota 55123
Delton
Job Details:
05/17/2022
"Replaced water valve and spliced in wires, tested and water valve works and ice maker cycles and fills. Refrigerator is working good."
We serviced a
SAMSUNG REFRIGERATOR
Model RF263BEAESR/AA
Near Rosemount, Minnesota 55068
Delton
Job Details:
05/17/2022
"Replaced drain kit, defrost thermistor, added fresh food heat kit. Tested and refrigerator is cooling and working good.; used 1 DA82-01415A (DRAIN KIT), 1 SH502 (HEATER), and 1 DA32-10104N (TEMP SENSOR) from stock"
We serviced a
MAYTAG WASHER TOP LOAD
Model PAV2200AWW
Near Apple Valley, Minnesota 55124
Delton
Job Details:
05/17/2022
"Washer had no power. Found that it was plugged into surge protector that had a GFI build in and was tripped. I reset surge protector and washer turns on. Tested and washer fills, agitates, drains and spins. Washer is working good."
We serviced a
SAMSUNG DISHWASHER
Model DW80R7060US/AA
Near Apple Valley, Minnesota 55124
Delton
Job Details:
05/17/2022
"Pulled out dishwasher and checked drip pan and was dry but i could tell there was water at one time as there was water marks. I tested and let dishwasher run for over 20 minutes and found no leaks, drained and checked all connections and did not find anything. I told customer to use as normal and if happens again to call back because I cannot find any leaks or drips as Im here testing it. Dishwasher is working good."
We serviced a
GE FREEZER
Model FUF21DLRDWW
Near Becker, Minnesota 55308
Seth
Job Details:
05/17/2022
High temp alarm every 6 hours. Upon arrival and inspection I found frost at the top of the freezer. I pulled the unit apart and steamed the evaporator. I did a refrigeration test and found that it was unable to frost up the evaporator completely. This unit has a failing sealed system .; saved tckt
We serviced a
MAYTAG DRYER- GAS
Model MGDB800VQ0
Near Minneapolis, Minnesota 55436
Adam
Job Details:
05/17/2022
Unit wouldnt spin. Found once disassembled that the idler was busted and the back two rollers were stiff. Customer had his own idler and roller to use. Let him know we wont warranty the parts but I can install them. Unit also needed a belt. Reassembled now unit is working properly ; used 1 WP8547157 (CABRIO BELT) from stock
We serviced a
GE WASHER FRONT LOA
Model GFW850SPN0RS
Near Minnetonka, Minnesota 55305
Nate
Job Details:
05/17/2022
"They had a new OEM boot that I installed, and I cleaned out a ton of mineral build up between tubs where water drains via the boot holes. But still leaking from front. ; schdld next appmnt for 5/19 THU !"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM7
Near Big Lake, Minnesota 55309
Seth
Job Details:
05/17/2022
I replace the sump with pump and clean the spray arms. I tested it and it filled a glass in 30 seconds. The dishwashers now working as designed.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ00
Near Lakeville, Minnesota 55044
Delton
Job Details:
05/17/2022
Customer said that food was soft in freezer on Sunday and then customer unplugged and plugged unit back in and food was cold and freezer foods were frozen late Monday. As Im here refrigerator fresh food is cold at correct temperature and freezer foods are frozen and ice is being made. I went into service mode and checked all functions and is all working or passed.I check fresh food evaporator and there is no frost build up that could cause poor cooling per the service bulletin. All functions are working good. I cannot find any failure or anything wrong as Im here.What i suspect happened is that water spilled/overflow from the dispenser and water got into the Deli drawer board and that would cause weird things happen and when it dried up refrigerator is functioning normally. (Common issue of these symptoms)Customer will keep an eye on it and call back if problem persists.
We serviced a
AMANA RANGE- ELECTRIC
Model ACF4215AW
Near Clearwater, Minnesota 55320
Seth
Job Details:
05/17/2022
"Customer complains that the bake option will either work or when it not work but when it works it sticks on. They also complain the right front burner only works on the high setting and does not heat unless they advance the knob. Upon arrival and inspection I found the customers complaints were duplicatable. I found the infinite switch is failed and the ERC control are both discontinued. Please source parts or to authorizations. 31926703 - switch, 31992501 - erc control; saved tckt"
We serviced a
SAMSUNG DISHWASHER
Model DW80K7050UG/AA02
Near Saint Michael, Minnesota 55376
Phillip
Job Details:
05/17/2022
I found water leaking from the diverter seal. Im ordering 2 seals. ; ordrd 2 DD62-00054A (Diverter seal)s
We serviced a
FRIGIDAIRE DISHWASHER
Model FFID2426TS0A
Near Apple Valley, Minnesota 55124
Delton
Job Details:
05/16/2022
"Ran the dishwasher to check for leaks and did not find anything. But found that dishwasher drained and that the sink backed up, so I suspect that it was sucking water back into dishwasher and then overfilling and then was leaking. I showed customer how sink was not draining and that they should make habit of running garbage disposal before starting dishwasher to prevent this issue. I cleaned out filter and has a lot of grease. She had a dishwasher cleaner tablet that i ran as i left to cleaned out inside of the grease build up. Dishwasher is not leaking as Im here. She will call back if problem continues.She has signed up for the service plan."
We serviced a
GE DRYER- GAS
Model GFD85GSPN0DG
Near Minneapolis, Minnesota 55426
Nate
Job Details:
05/16/2022
"The front drum support is jagged inside and it rips clothes. Needs new drum support WE13X29593. ; saved tckt"
We serviced a
SAMSUNG REFRIGERATOR
Model RF4287HARS/XAA
Near Minneapolis, Minnesota 55416
Nate
Job Details:
05/16/2022
"Bottom of freezer and below evap all iced up. Steamed out all the ice. Took back panel off fridge, found the drains all gummed up. Adjusted them, cleaned and steamed them out. Drains great now. Found a leaking waterline. Replaced 4 section, and used to John guest fittings. Not leaking water anymore. used 2 Fitting3 (1/4' JG CONNECTOR) from stock"
We serviced a
FRIGIDAIRE MICROWAVE
Model FMV156DCC
Near Minneapolis, Minnesota 55408
Nate
Job Details:
05/16/2022
"Not running. Needed a new microswitch for the receiving latch. Replaced that, tested it, runs well and heats now.; used 1 MICRO8 (1/4' MICROSWITCH) from stock"
We serviced a
GE REFRIGERATOR
Model CFCP1NIXBSS
Near Minneapolis, Minnesota 55419
Nate
Job Details:
05/16/2022
"Still not cooling. Found the evaporator iced over. Steamed it off, bypassed bi metal, jumped heater at board and heater came on great. Installed new bi metal. Tested ohms at temp sensor for freezer and thats good. Should cool now. Evaporator fan running great.; used 1 WR50X60 (DEFROST BIMETAL) from stock"
We serviced a
LG WASHER TOP LOAD
Model WM2301HR
Near Minneapolis, Minnesota 55419
Nate
Job Details:
05/16/2022
"Filter board is bad, but after replacing it, main PCB is bad too. "
We serviced a
GE REFRIGERATOR
Model GSHF5KGXCCBB
Near Farmington, Minnesota 55024
Delton
Job Details:
05/16/2022
"Replaced control board, tested and no errors and all functions are working good.; used 1 WR55X10942P (MAIN BOARD) from stock"
We serviced a
FRIGIDAIRE DRYER- GAS
Model FARG1011MW0
Near Minneapolis, Minnesota 55417
Nate
Job Details:
05/16/2022
Not drying clothes. Temps with vent connected shoot up to 190. With vent disconnected 150. Mph outside is 16 at best. 26 behind dryer. Vacuumed out lint and water inside dryer. Dryer works great. Need to get vent cleaned.
We serviced a
WHIRLPOOL WASHER TOP LOAD
Model WTW5005KW0
Near Minneapolis, Minnesota 55407
Nate
Job Details:
05/16/2022
"Customer said washer isnt agitating or spinning maybe? And that a black cord was disconnected. I found the drain line was no longer going into the wash tub. I routed it into the wash tub, and attached it with a zip tie. Put it on a drain and spin, it spins great. Put it on a casual wash, it filled with water and then agitated great. I then put it on a drain and spin, it drained awesome and spun out. Everything working great. Nothing underneath the washer thats concerning with transmission, belt etc."
We serviced a
FRIGIDAIRE WASHER FRONT LOA
Model FTF530FS1
Near Saint Michael, Minnesota 55376
Phillip
Job Details:
05/16/2022
The customer said its loud when it spins. I put the washer into spin and its very loud. The basket has some wobble to it. The rear tub bearing and basket are bad.
We serviced a
GE REFRIGERATOR
Model GFE28HSHESS
Near Saint Michael, Minnesota 55376
Phillip
Job Details:
05/16/2022
The upper portion of the fresh food was not cooling well. The fresh food fan was running but it was going a little slow. I defrosted the evaporator and replaced the fan. There was a firmware update needed so I updated the firmware. ; used 1 WR60X26866 (FRESH FOOD FAN) from stock
We serviced a
BOSCH DISHWASHER
Model SHX7PT55UC/04
Near Osseo, Minnesota 55311
Phillip
Job Details:
05/16/2022
The customer said the dishwasher does not clean well. I tested there hot water and its over 20 grains of hardness. The main sump filter was dirty. One of the upper rack holders were hanging down and keeping the spray arm from spinning. I also found food and debris clogging the rack spray arm. I cleaned the spray arms and filter. I advised the customer to have the softener repaired.
We serviced a
GE WASHER FRONT LOA
Model GFW550SSN2WW
Near Annandale, Minnesota 55302
Seth
Job Details:
05/16/2022
I replaced the crushed hose and tested.the washer is now fixed.
We serviced a
SAMSUNG RANGE- ELECTRIC
Model NE595R0ABSR/AA
Near Big Lake, Minnesota 55309
Seth
Job Details:
05/16/2022
"Not heating right. DG47-00055A - broil element"
We serviced a
SPEED QUEEN WASHER TOP LOAD
Model AWN432SP113TW04
Near Dayton, Minnesota 55327
Adam
Job Details:
05/16/2022
Customer complaint is water leaking under unit disassembled unit. Went through cycles functions and wouldnt leak. There is a floor drain two feet to the left of the washing machine. Have a feeling that water comes out from the drain and then goes under the washer. Let tenant know to watch and see what happens. I did add photos of the drain and the water coming up
We serviced a
LG WASHER FRONT LOA
Model WM2301HR
Near Big Lake, Minnesota 55309
Seth
Job Details:
05/16/2022
Customer complains the washer gets an uneven balance load error often and it leaks. Upon arrival and inspection I found the door boot was torn and the rear main bearing has failed causing the torn door boot and leak.
We serviced a
GE DISHWASHER
Model GDT665SMN4ES
Near Big Lake, Minnesota 55309
Seth
Job Details:
05/16/2022
"Customers complaint with the two week old dishwasher is it at leaks when it runs. Upon arrival in inspection I found the unit had a broken sump housing and drain pump assembly. Its obvious something has impacted the unit from the bottom cracking both the lower and upper parts of the housing, damaging the pump, and damaging the sensor. We would need the following parts to complete repair. WD19X28199 - sump, WD21X22830 - sensor, WD19X25461 - drain pump. The customer has extensive damage to the floor cabinets and ceiling of finished basement area. Please hold off from purchasing any parts or moving forward until she speaks with her insurance company and GEs insurance company. She is going to try to work with Home Depot and her homeowners insurance to figure out what next steps look like for her.; saved tckt"
We serviced a
JENN-AIR COOKTOP- GAS
Model JGD8430ADB
Near Osseo, Minnesota 55311
Phillip
Job Details:
05/16/2022
"The complaint was the front right burner is slow to light and the fan switch is broken. I found several things wrong and many parts are needed. First off the main glass top has a large crack. The rotary switch turns hard thats why the knob keeps cracking. All of the burner heads have been drilled out with the screws left in the burner holders and the burner heads are held down with silicone. To fix it right it will need the manifold, all burner holders, screws, knobs, rotary switch, glass top. I may find more issues once its apart. I told the customer it would be. 2 person job and a extra fee of 150. Please see whats approved. Manifold pipe assembly 74010771Ridge front burner 74010772Right rear burner 74010773Left front 74010774Left rear W11416836Rotary switch WP74010783Burner screw (8) WP8273062-will need 8Burner knobs (4) WP7733P410-60-will need 4Fan knob (1) WP7737P245-60- need 1 Glass top W10204669; snapped 5 QuickPics, states that autho needed"
We serviced a
KITCHENAID GARBAGE DISPOSAL
Model KGIC300H1
Near Maple Grove, Minnesota 55369
Phillip
Job Details:
05/16/2022
I replaced the garbage disposal. ; used 1 DISPOSAL () from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDEM01
Near Plymouth, Minnesota 55446
Phillip
Job Details:
05/16/2022
"I replaced all parts I ordered. I completely defrosted the evaporator and moved the new thermistor to the new spot according to the service bulletin. I changed the defrost mode to a standard 8 hour run. The customer said that after I left the drawers were making noise and the control beeping stopped. The alarms got turned off, I turned them back on and when I put the drawers back in they sounded fine."
We serviced a
FRIGIDAIRE COOKTOP- ELE
Model FEC30S6ABB
Near St. Cloud, Minnesota 56301
Seth
Job Details:
05/16/2022
I replaced the failed switch and tested the cook top. The cook top is now fixed.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ05
Near Fridley, Minnesota 55432
Adam
Job Details:
05/16/2022
"Unit not making ice. On arrival unit was full of ice. On switch was on. Held the test button for 3 seconds to bring it through the cycles and it went through all the cycles. Customer said they have done that a few times and it works for a day or two then stops. Unit needs a new ice maker. Something wrong with motor or bailing arm. W11284458 ice maker; O-emld tckt , states that autho needed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF263BEAESR/AA
Near Rosemount, Minnesota 55068
Delton
Job Details:
05/16/2022
"Has the evaporator fresh food evaporator freezing over issue and leaking. Freezer foods is frozen. I informed customer that there is a fix but since there is a large ice build up, i cannot pull off evaporator cover. I informed customer that fridge will need to be unplugged and doors opened so it can thaw and i can pull off cover and do the fix. Have all the parts truck stock. Rescheduling customer for tomorrow.; schdld next appmnt for 5/17 TUE !"
We serviced a
GE RANGE- ELECTRIC
Model J2B918SEK3SS
Near Minneapolis, Minnesota 55439
Adam
Job Details:
05/16/2022
Unit display is dead. Getting power to unit and to control board. Top burners are working as well. Unit needs a new control board. WB27K10124 control board. ; states that autho needed
We serviced a
WHIRLPOOL DRYER- ELECTRIC
Model LEQ8611PW0
Near Eden Prairie, Minnesota 55347
Adam
Job Details:
05/16/2022
Unit wouldnt start. Timer would tick but wouldnt start. Tested timer switches and found was a bad fuse. Replaced thermal fuse and cleaned out all the lint and oiled up the rollers. Now unit is working good; used 1 WP3392519 (THERMAL FUSE) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED5FVGXWS00
Near Eden Prairie, Minnesota 55347
Adam
Job Details:
05/16/2022
Unit was building up with ice on the bottom of freezer. Found the defrost drain was plugged. Removed hose and cleaned out debris that was built up. Then steamed out ice. Now unit is working great
We serviced a
GE REFRIGERATOR
Model PFS22SISBSS
Near Eagan, Minnesota 55123
Delton
Job Details:
05/16/2022
"Replaced door parts, seems to work and now latches inside and holds door shut better. Explained to customer that door will feel more tight because both sides of door latch was broken. Door is shutting and sealing."
We serviced a
SAMSUNG WASHER TOP LOAD
Model WA50F9A6DSW/A2
Near Chaska, Minnesota 55318
Adam
Job Details:
05/16/2022
Unit would power up but wouldnt do anything. Unit is under recall. Gave customer info to get into contact with Samsung and to have matters settled
We serviced a
WHIRLPOOL WASHER TOP LOAD
Model WTW57ESVW1
Near Sartell, Minnesota 56377
Seth
Job Details:
05/16/2022
"Only spins wont fill, or agitate. The timer has failed. I was an able to test the ATC. I quoted both ways. ."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFTR1814QW4A
Near Saint Paul, Minnesota 55105
Delton
Job Details:
05/16/2022
Found that evaporator fan motor was locked up. I Replaced evaporator fan motor.Refrigerator is cooling and working good now.
We serviced a
MAYTAG CLEANING- DRYER
Model MCE8000AYW
Near Minneapolis, Minnesota 55419
Delton
Job Details:
05/16/2022
"Was able to pull off front and get to the inside of dryer. Cleaned, vacuumed, and inspected belt, rollers and all looks good. I checked heat and it cycles good. Dryer is working good."
We serviced a
GE REFRIGERATOR
Model PSC23SGRCSS
Near Chanhassen, Minnesota 55317
Adam
Job Details:
05/16/2022
Unit isnt keeping cool temps in freezer. This unit has a sealed system failure. Compressor is running but the frost pattern on the evap is only half and full of frost. Fans and defrost heater tested good. See photos
We serviced a
FRIGIDAIRE DISHWASHER
Model FFBD2412SS2A
Near Eagan, Minnesota 55122
Delton
Job Details:
05/16/2022
Customer says dishwasher is full of water and leaks even when not in use. Sounds like water valve is failing and not fully closing. But also there is no high loop and sink was backing up and could cause back fill from sink into dishwasher. Owner will think about it and call back if they want to proceed. will need to order water valve part# 80707901
We serviced a
TAPPAN RANGE- GAS
Model TGFS26CSB
Near Minneapolis, Minnesota 55414
Nate
Job Details:
05/16/2022
The gas company turned off the gas to the house.There was a leak coming from the pipe that comes up through the floor to the range. Thats why it doesnt work. No gas coming to it. And also the pipe behind range is crimped and theres a crack. .
We serviced a
UNKNOWN WASHER TOP LOAD
Model n/a
Near Brooklyn Center, Minnesota 55429
Phillip
Job Details:
05/16/2022
"The washer is leaking water from the bottom, the agitator is broken and the front panel screws are rusted so I cannot remove the front. The model tag is warn off so I cant read it. "
We serviced a
GE RANGE- ELECTRIC
Model JB655YK9FS
Near Hopkins, Minnesota 55343
Adam
Job Details:
05/12/2022
Installed busted element. Tested with customer. Unit is back to working properly
We serviced a
WHIRLPOOL DRYER- ELECTRIC
Model WGD8410SW2
Near Eden Prairie, Minnesota 55346
Adam
Job Details:
05/12/2022
Had F1 error code which means the board has failed. Found once disassembled the relay was burnt up. Attempted to repair board. Everytime would still blow the relay. Will need new control board
We serviced a
LG DISHWASHER
Model LDT7808SS
Near Eden Prairie, Minnesota 55347
Adam
Job Details:
05/12/2022
"Unit leaking from front left side. Found when testing was leaking from the door gasket area. Ordering both tub and door gasket. Reschedule for Wednesday the 183920DD3005F3920DD3002D; ordrng 1 3920DD3002D (Gasket tub), ordrd 1 3920DD3005F (Door gasket)"
We serviced a
KENMORE DISHWASHER
Model 66513592K600
Near Chaska, Minnesota 55318
Adam
Job Details:
05/12/2022
Customer complaint unit wouldnt start. I would drain. I hit the normal cycle and it fired up right away. There was a lot of soap suds in there which could effect why certain operations. Cleaned out all the soap suds and then ran unit on multiple different cycles every cycle it started
We serviced a
MAYTAG WASHER TOP LOAD
Model LAT9356AAE
Near Excelsior, Minnesota 55331
Adam
Job Details:
05/12/2022
Unit was shaking a lot during spin. Found the rear leg wasnt tight so I balanced the washer and tightened the legs. Now unit is running goid
We serviced a
GE REFRIGERATOR
Model GNE27JYMNFFS
Near Buffalo, Minnesota 55313
Seth
Job Details:
05/12/2022
Makes a rod knock noise when compressor starts. I pulled the fridge and removed the zip-tie holding the drain hose to the compressor. The noise went away instantly. I checked for bulletins and errors unit was fine.
We serviced a
WHIRLPOOL WASHER FRONT LOA
Model WFW87HEDC0
Near Big Lake, Minnesota 55309
Seth
Job Details:
05/12/2022
I installed the redesigned drain pump and tested the washer. It got lost a few times but after resetting the acu I was able to get the unit. To respond and complete a quick wash cycle. The washer is now working as designed.; used 1 WPW10605427 (DRAIN PUMP) from stock
We serviced a
GE MICROWAVE
Model JVM1540LM2CS
Near Plymouth, Minnesota 55446
Nate
Job Details:
05/12/2022
"Microwave stopped after 5 seconds. Replaced magnetron today. Ran it for 2, 2, and 4. Never cycled off prematurly, runs great, heats great."
We serviced a
ELECTROLUX DISHWASHER
Model FGHD2465NF1A
Near Elk River, Minnesota 55330
Matt
Job Details:
05/12/2022
"Customer complaint is, LEAKING INTO THE KITCHEN. Inspected and tested. The tub gasket and bottom door gasket are falling apart. Installed new tub gasket, bottom door gasket and side shield kit and tested. Dishwasher is not leaking. Dishwasher is now fixed. This dishwasher is in really rough shape. The tub is plastic and its warping all over and is going to be a issue in the near future. The top is warped really bad and the bottom is warped up and scraping on the bottom door gasket. This thing really just needs to be replaced if it leaks again. ; used 1 809006501 (THE INFAMOUS BOTTOM WIPER), 1 154827601 (TUB GASKET), and 1 154701001 (SPLASH SHIELD KITS) from stock"
We serviced a
GE WASHER FRONT LOA
Model GFW650SSN2WW
Near Minneapolis, Minnesota 55437
Nate
Job Details:
05/12/2022
Replaced bad valve. Water isnt leaking into tub and gasket anymore. It was leaking before.
We serviced a
GE REFRIGERATOR
Model CFCP1NIXBSS
Near Minneapolis, Minnesota 55419
Nate
Job Details:
05/12/2022
Replaced bad board. Customer will give it 24 hours to cool down.
We serviced a
KITCHENAID RANGE- ELECTRIC
Model KSEG950ESS2
Near Blaine, Minnesota 55449
Matt
Job Details:
05/12/2022
"Customer complaint is, CONTROL PANEL BUTTONS ARENT WORKING FOR THE OVEN. Inspected and tested. Found some of the buttons on the control panel dont respond. Needs a new control panel. Installed new control panel and tested. Still not working. Now I found mouse poop all over the inside and on the main board. Customer wants us to order the 2 harnesses that go from the main board to display board and touchpad. Installed the 2 harnesses and still not working. Customer approved installing the main board. Installed new main board and tested. Everything is working great now. Range is now fixed."
We serviced a
LG WASHER FRONT LOA
Model WM2077CW/01
Near Mound, Minnesota 55364
Adam
Job Details:
05/12/2022
Customer complaint is tub sitting lopsided. Disassembled unit and found the bearing was bad. Also the unit shredded the front boot also. Customer doesnt want to repair unit being such a costly repair
We serviced a
SAMSUNG DRYER- GAS
Model DV40J3000GW/A2
Near Becker, Minnesota 55308
Seth
Job Details:
05/12/2022
Replace the failed idler pulley and tested it. The dryer is now fixed.; used 1 DE634A (PULLEY) from stock
We serviced a
SAMSUNG REFRIGERATOR
Model RFG297AARS/XAA
Near Eagan, Minnesota 55122
Delton
Job Details:
05/12/2022
Put inverter board back in and compressor turns on and is running. Refrigerator is starting to cool and is working good.
We serviced a
FRIGIDAIRE RANGE- ELECTRIC
Model FFEF3043LSP
Near Maple Grove, Minnesota 55369
Matt
Job Details:
05/12/2022
"Customer complaint is, BURNER MADE LOUD NOISE AND WON'T TURN ON ANYMORE AND OVEN NOT WORKING EITHER. Inspected and tested. Found the front left element is fried and the power relay on the board is also fried. Needs a new board and element. ."
We serviced a
SAMSUNG REFRIGERATOR
Model RF263BEAESR/AA
Near Rogers, Minnesota 55374
Phillip
Job Details:
05/12/2022
"I replaced the defrost sensor and drain kit, this module does not need the heater. I also adjusted the ice maker fill tube and sealed the ice maker cabinet."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ00
Near Plymouth, Minnesota 55446
Phillip
Job Details:
05/12/2022
"The whole unit was not running at all. I put into a diagnostic mode and then back out. It started running but then shut off 2 minutes later. It will need the rear main board. I was unable to find the part. Please locate the part and contact the customer. I added a pic of the quote. Board W10843055; snapped 1 QuickPics, states that autho needed"
We serviced a
GE REFRIGERATOR
Model PSS26SGPASS
Near Maple Grove, Minnesota 55311
Phillip
Job Details:
05/12/2022
"Issue just started and got worse. I found water leaking from the ice maker mold and then ice forms around the shut off arm. The drive gear on the back of the ice bin is cracked in half. I replaced the ice maker. It cycled and does not leak. Dana is shipping the customer a new ice bin. ; used 1 WR30X10093 (ICEMAKER), and 1 WR17X11447 (Ice bin) from stock"
We serviced a
MAYTAG CLEANING- DRYER
Model MCE8000AYW
Near Minneapolis, Minnesota 55419
Delton
Job Details:
05/12/2022
Could not clean all the way. Has a shirt dryer on top and would have to take off whole top to pull apart front to get inside dryer (see picture). Customer didnt want to do that.
We serviced a
KENMORE DRYER- ELECTRIC
Model 11062822101
Near Rogers, Minnesota 55374
Matt
Job Details:
05/12/2022
"Customer complaint is, DOOR NOT STAYING CLOSED. Inspected and tested. Found the door latch is broken. Installed new door latch and tested. Dryer is now fixed. ; used 1 279570 (LATCH KIT) from stock"
We serviced a
HOTPOINT DRYER- GAS
Model DLL1550AALWH
Near Saint Paul, Minnesota 55106
Delton
Job Details:
05/12/2022
"Dryer not heating. Also sometimes the dryer will just keep running and wont shut off by itself, even on timed dry, also is noisy when tumbling. Found that several things are bad. Gas coils, timer, bearing and front seal.Gas coils WE04x0581; timer WE04X0520; Seal WE09X0030; bearing kit WE25m40; saved tckt"
We serviced a
MAYTAG WASHER FRONT LOA
Model MAH3000AWW
Near Minneapolis, Minnesota 55416
Nate
Job Details:
05/12/2022
"Not draining water. Took apart all the internal drain line components, including the drain pump. Didnt find a ton of debris. Cleaned it all out though. Drains great now. Door doesnt lock though. Found a burned board and bad door lock. Wont go into spin. Quoted for those, customer buying a new one. Washer over 20 years old."
We serviced a
MAYTAG DRYER- GAS
Model MGDC400VW0
Near Inver Grove Heights, Minnesota 55076
Delton
Job Details:
05/12/2022
"Found that thermal fuse is open cutting power to igniter. Replaced thermal fuse and cycling thermostat. Also cleaned inside dryer of lint build up. Tested and dryer is cycling heat and since its heating dryer timer is moving. Without heat timer wouldnt advance in automatic dry but it is now .Dryer is heating and working good.; used 1 WP3392519 (THERMAL FUSE), and 1 WP3387134 (THERMOSTAT) from stock"
We serviced a
GE GARBAGE DISPOSAL
Model gfc525n
Near Maple Grove, Minnesota 55369
Phillip
Job Details:
05/12/2022
The disposal is loud and cracked in the side and water is leaking from it. Im coming Back Monday to replace the disposal. ; used 1 gfc525n (DISPOSAL) from stock
We serviced a
GE DISHWASHER
Model PDT715SYN0FS
Near Plymouth, Minnesota 55446
Phillip
Job Details:
05/12/2022
The dishwasher was drains slow. I removed the hoses from the air gap. I found plastic and Legos stuck in the hose and air gap. I hooked it back up and now it drains good.
We serviced a
GE REFRIGERATOR
Model PFS22SISBSS
Near Eagan, Minnesota 55123
Delton
Job Details:
05/12/2022
"Checked and refrigerator is at correct temperature and evaporator appears to have good frost pattern, ice is being made. Appears that cooling system is good. I suspect that the door was left open. Found that the French door seal plastic tab has broke off ? If so, part# WR24x10173; saved tckt"
We serviced a
SAMSUNG WASHER FRONT LOA
Model WF328AAW/XAA
Near Minneapolis, Minnesota 55446
Phillip
Job Details:
05/12/2022
The washer was trying to drain but the drain pump was buzzing. I pulled the drain motor off and found a chunk of metal in the pump. I removed the metal. The washer fills and drains good now.
We serviced a
WHIRLPOOL DRYER- GAS
Model WGD5000DW1
Near Osseo, Minnesota 55311
Phillip
Job Details:
05/12/2022
The dryer would not heat. I found the gas was turned off to the dryer. I turned the gas back on and its working. The customer had if off when they had the floor tiled.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRS20ZRGW6
Near Apple Valley, Minnesota 55124
Delton
Job Details:
05/12/2022
Found that evaporator is frosted over and no air flow going to fresh food side. Forced defrost and found that defrost bimetal is bad. Also defrost timer is suspect. Ordering parts and rescheduling. Meanwhile i defrosted evaporator so it will cool till i get back.; ordrd 1 215846602 (Defrost timer) and 1 Wp4387490 (Defrost bimetal)
We serviced a
SAMSUNG DRYER- ELECTRIC
Model DV48J7700EW/A201
Near Otsego, Minnesota 55301
Matt
Job Details:
05/12/2022
"Customer complaint is, WILL NOT START. HAS POWER AND ALL BUTTONS WORKS BUT WILL NOT START THE DRUM. Inspected and tested. Found the idler pulley has failed and fallen off, also the rear right roller has failed. Quoted customer $196. to install 2 new rear rollers and a idler pulley. Customer approved repairs. Installed 2 rear rollers and idler pulley. Tested dryer and its working great. Dryer is now fixed. ; used 1 DE634A (PULLEY), and 2 4581EL2002h (ROLLER) from stock"
We serviced a
MAYTAG DRYER- ELECTRIC
Model MGD6630HW
Near Maple Plain, Minnesota 55359
Adam
Job Details:
05/12/2022
Unit was heating. Checked air flow right away and was only getting 10-12mph out of the house so not the best. Disassembled front of unit and found the igniter would glow and then wouldnt light. Found that the gas was shut off to the unit. Turned gas back on now unit works properly
We serviced a
WHIRLPOOL DISHWASHER
Model DWHD440MFP/08
Near Minneapolis, Minnesota 55416
Nate
Job Details:
05/12/2022
"Dishwasher not mounted, it moves around. Used mounting brackets to attach it. Nice and sturdy now.; used 2 WP8269145 (MOUNTING BRACKET), and 1 W10426979 (MOUNTING BRACKET) from stock"
We serviced a
WHIRLPOOL WASHER TOP LOAD
Model LTE5243DQ6
Near Minneapolis, Minnesota 55417
Nate
Job Details:
05/12/2022
"Replaced a bad lid switch because lid switch on there wasnt working . Spins great now. Dryer was overheating. Cleaned a ton of lint out of dryer. Now runs at 209, was 220 before. With vent connected it shoots up to 235 and I stopped it. Need to have vent cleaned out. ; used 1 3949247V (LID SWITCH) from stock"
We serviced a
SAMSUNG REFRIGERATOR
Model RF20HFENBSR/AA
Near Eagan, Minnesota 55122
Delton
Job Details:
05/12/2022
"Found that fresh food evaporator is frozen over, can see ice build up through the vent holes (see pictures) i ran test and getting defrost error. Service bulletin shows to replace control board for similar issue. Customer approved estimate. Ordering parts and rescheduling.Informed tenant that fridge would need to be unplugged 48 hours before so all ice build up will melt so i can gain access to evaporator.; ordrd 1 Da96-00845a (Evap assembly) and 1 Da92-00420s (Control board)"
We serviced a
AMANA DISHWASHER
Model ADB1400AGS1
Near Albertville, Minnesota 55301
Matt
Job Details:
05/12/2022
"Customer complaint is, DOOR SEAL IS BROKEN. Inspected and tested. Found the door gasket is falling apart. Installed new door gasket and tested. Dishwasher is now fixed."
We serviced a
KITCHENAID DISHWASHER
Model KDTE104ESS1
Near Albertville, Minnesota 55301
Matt
Job Details:
05/11/2022
"Customer complaint is, NOT CIRC WATER. Inspected and tested. Found the circulation pump has failed.. to install new pump. Customer approved repairs. Installed new circulation pump and tested. Dishwasher is working great. Dishwasher is now fixed. ; used 1 W11032770 (WASH MOTOR) from stock"
We serviced a
ELECTROLUX WASHER FRONT LOA
Model EFLS527UIW0
Near Otsego, Minnesota 55301
Matt
Job Details:
05/11/2022
"Customer complaint is, LEAKING BY THE DOOR AND LEAKING ONTO THE DRAWER BELOW. Inspected and tested. Found the water was coming from the dispenser and leaking down the front. Removed dispenser and it was really gunked up inside. Cleaned up inside of dispenser housing and tested. I cant get it to leak again. Looks like it was just all gunked up. If it leaks again, we will need to order the whole dispenser assembly and drawer."
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED5SHAXMQ10
Near Eagan, Minnesota 55122
Delton
Job Details:
05/11/2022
Replaced dispenser switch bracket. Tested and paddles now hit switch correctly. Dispenser is working good.; pckd up 1 Wp2180226 (Dispenser switch bracket)
We serviced a
WHIRLPOOL RANGE- ELECTRIC
Model RF362LXSS0
Near Rosemount, Minnesota 55068
Delton
Job Details:
05/11/2022
"Customer states that it only shows 6 minutes to preheat and when oven says its done preheating that the oven thermometer they bought only shows 250 degrees. I tested with my digital thermometer and it during preheat it did pause the time it showed so actually added time and when the oven showed preheat was done it was at 350 degrees, i showed this to customer.The user manual also suggests that you wait 10 minutes after the oven says its done preheat to put into some foods for baking. I tested the calibration of oven and my thermometer is very close to what oven says. I suggested to customer that to get digital thermostat if they want to knew exact. I also informed that oven heat will cycle and get a high/low and the average will be the set temperature.Oven is heating and working good."
We serviced a
MAYTAG DRYER- GAS
Model n/a
Near Richmond, Minnesota 56368
Seth
Job Details:
05/11/2022
"I replace the blower igniter and coils. The dryer no longer makes noise and heats perfectly.; used 1 279311 (IGNITER), and 1 5303931775 (COIL KIT) from stock"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FGHS2631PF3
Near Saint Michael, Minnesota 55376
Phillip
Job Details:
05/11/2022
I found the damper stuck wide open. The damper motor was frozen. I thawed out the motor but Im ordering a new one to replace. Charging for part only no labor. ; ordrd 1 241853801 (Damper)
We serviced a
WHIRLPOOL WALL OVEN- ELECT
Model RBD305PVS02
Near Plymouth, Minnesota 55446
Phillip
Job Details:
05/11/2022
I installed the main control. The display is nice and bright and both ovens heated to 350.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ02
Near Plymouth, Minnesota 55446
Phillip
Job Details:
05/11/2022
The display was not responding and showing dashes. The board would not reset. I replaced the main board and programmed it. Its all working good. ; used 1 WPW10503278 (JAZZ BOARD) from stock

