Pulled unit out to install inverter from last diagnosis. Hooked up SmartHQ and is now reading something with the three way valve. Compressor still not turning on. Installed new inverter. Turned on unit and the compressor kicked on but sounded terrible. Hooked up gauges now unit is is above a vacuum. Unplugged unit and got equalized pressure was reading almost 2 which indicates a restriction. Drained out the Freon outside properly. Found a restriction in the condenser. Pressured with nitrogen. A bunch of nasty oil and rusty like substance. Got it cleared out the best I could rebrazed then pressurized and found it was restricted again cut out the condenser again. Pressurized and this time wont clear out. Its cut away past the brazes. The debris must have clogged it. Will need a condenser. The customer also mentioned the compressor making really bad noises. It was also so hot it started to warp the inverter. Will need a new condenser. Also will neeed a new compressor. Would recommend also three way valve because of the debris and error code. WR87X32099 condenser WR86X32075 3 way valveWR87X32290 compressor. ; states that autho needed

I dont have the parts. I rescheduled customer for Monday. Please schedule me 2 hours. ; schdld next appmnt for 11/20 MON !

"Customer complaint- the freezer door shuts hard. Removed door, removed the slide and checked found the bearings were worn out. Informed customer, the customer approved the repair ; ordrd 1 W11658403 (Slide)"

"Not running. Found a bad belt and a ton of lint in dryer, along with a bad pully and two bad rollers. Vacuumed out all lint. Replaced rollers and cleaned and oiled shafts. Replaced pully and belt. Runs great now

Customers complaint unit not draining. Will give E24 for drain error. Verified complaint. Pump sounded ok and was only getting a trickle of water. Removed drain hose to clean out line right at the end of drain hose found a bunch of debris. Cleared out blockage tested now unit is draining properly.

Replaced bad detergent dispenser. Works great now. Old one was broken.

"Found that the igniter is weak and not turning on gas to heat oven. Also the mechanism that holds in and springs open the warming drawer, plastic is not locking and there is a service bullitin that it is subbed to a new part. Customer wants the oven igniter replaced but will hold off on the warming drawer lock mechanism.Replaced igniter, tested and oven preheated and is working good.

Ignitor for bake isnt coming on. Replaced bad bake ignitor. Ignites great now. Wall oven.

"Squealing when it runs. Found a bad idler pully and roller. Installed rollers. Sounds great now though. I cleaned roller shafts and oiled them, and vacuumed out dryer."

There complaint is the dryer takes a long time to dry. We started the dryer and found it does heat. The air flow test said the air flow is poor. I preformed a heat test and the dryer only heats to 140 and it takes a long time. I disconnected the vent and it gets to 190 and the air flow tested good. Advised the customer the issue is with there dryer duct to the outside. They had the roof redone a few weeks ago. Its possible someone covered the duct hole. I gave the customer a couple numbers to call for duct cleaning.

"I tested the dishwasher when I got here. Tried a cancel and drain and it drained great. Spoke with customer and theyve been using the same detergent for a long time. Havent switched detergent in a long time. Asked if they used any cleaner in the dishwasher. No, then I asked if they used any dishwasher detergent for hand washing and they said yes. I ran it for a minute and a lot of suds. I put olive oil in the dishwasher and let it circulate and after doing that twice, all the suds are gone now."

"Stops after 20 minutes of running. When I got here from what she described it sounded like theres blockage in the vent. I did a vent cleaning and a ton of lint came out. Redid the vent tape on the vent. Ran it for 20 minutes which is how long it goes before shutting off. Didnt shut off. Everything checks out good now.

Today I replaced the control panel. All the buttons work and it heats.

The complaint is when the oven heats for about 10 minutes the fault f3e2 comes up. The fault is for the temperature getting too high. I tested the oven temperature sensor and it reads 1087 at room temperature. I verified the fault code. I replaced the temp sensor and the main control. I started the oven and let heat to 350 for about 15 minutes.

"Found that bake element is bad (broke in half) maintenance approved estimate. Picked up part, replaced bake element, tested and bake is now heating and working good.

"founded the burner tube was not aligned into the gas line adjusted to correct position. After that we tested and it works just fine with no issues .

Installed new valve from last diagnosis. Once installed tested multiple times. Unit is operating properly without leaks. Reassemble reinstalled and mounted as previously installed. Unit sits on uneven flooring from some putting thick wood flooring. Leveled best I can.

Replaced dryer fan motor tested dishwasher works good.

issues was no power from the power outlet . We reset main breaker this resolve problem machine runs good and verify heating cycle is back to operation works great.

"Customer complaint is, RUNS FOR 10 MIN THEN SHUTS OFF. Tenant says it does it on sensing and timed dry. Inspected and tested. I started a timed dry high heat cycle and it started heating and shut down in about 3 minutes. Heat had gotten to about 200F. I restarted dryer and now its running and heat is cycling perfectly between 210F and 110F consistently for over 30 minutes. I stopped it and let it sit for a few minutes and then restarted it and its not shutting down and working perfectly for another 30 minutes. I cant get it to fail again.

The customer complaint is when they dispense the ice water leaks down. I found the ice maker is frosting up and ice gets stuck together. When it dispenses ice the ice breaks up and causes frost. The frost on the ice chute melts and causes the water drips. We found the ice make fill tube was not adjusted. We defrosts the compartment and adjusted the fill tube.

"Customer complaint is, WHEN USING THE SURFACE UNITS THEY CAN SMELL ALOT OF GAS. Customer had just done a bunch of staining before they started smelling it. They only smell it while there using it. Inspected and tested. Turned on all 4 burners and watched them for about 5 minutes and there working perfectly and I didnt smell anything off. I explained to the customer that its burning fumes from the stain and to open up some windows and get the house aired out and that there going to keep smelling it until the fumes are gone."

Display is dead. Getting 120 volts to unit and to the control board. Checked the wiring from the display to the board everything is testing good with continuity. Looks like from the wiring diagram we only have two options left and thats the display board and PCB. Installed pcb but didnt do any difference. Will need display board. Looks like Jared said it might be NLA. ; states that autho needed

"Vent goes up but only part way. Sometimes you have to hold the button the entire time to get it to go up. Sometimes it drops quickly back down. Other times very slowly. Theres a receptical that was installed onto the front of the vent box which an electrician would need to have uninstalled, and the gas line would have to be uninstalled. Needs a motor and switch(es). JR is going to take it from here. ; saved tckt"

We adjusted door and added shims as need now door aligned evenly. Also we noticed that water valve for the ice maker is faulty in order to fix this issues we need to return back to replace Ice maker tray and water valve in order to complete repair . Please search and order water valve part and reschedule customer.; saved tckt

"We found several issues. There is frost building up behind the freezer panel. The fan is working and the drain is good. When its in defrost the heat is not staying on long enough to completely defrost the evaporator. The fresh food drain is plugged up and frost is coming through the fresh food evaporator cover vent holes. We also found water under the crisper drawers. It will need the freezer and fresh food defrost sensors, the drain kit and the main board. The drain kit shows out of stock. Please look up the drain kit and contact the customer with a return date. I left the owner a message with the price. Note I need to temp sensors. Also make sure they unplug the unit for 24 hours. I created an estimate. ; snapped 2 QuickPics, states that autho needed"

"Customer complaint is, DEAD. Inspected and tested. Found the UI is unresponsive. Customer power cycled it from the breaker box and after about 10 times it came on. I hooked up SmartHQ and theres no software update available. Quoted customer $640. to install new UI board and main board. Customer approved repairs. Parts on order. ; ordrd 1 WD21X24901C (Main board) and 1 WD21X31910 (UI board)"

"Dryer buzzes but wont run. Only if I give it a push while holding in the door switch and start switch. Has a bad motor and blower wheel. Quoted for this repair. 25 year old dryer. Tim said hes pretty sure hell want to do it, but has to double check with office. I put the two parts into my cart at Dey, on will call, but havent ordered yet. If he calls back and says lets do it, I told him we could put them on will call and I could be back tomorrow (as of now I have availability tomorrow). ; saved tckt"

"Spent 45 minutes driving to this place and no one home and no answer. Dana called customer and they will have to reschedule. Bummer since it was far drive.; saved tckt , states that autho needed"

"Installed bridge board first going off what GE believe is the problem. Once installed tested same issue. GE says if that doesnt work would need the control board WB27X27172. Its a special order part. Left voicemail quoted blue book for both boards and labor. If he gives the go ahead Jared had source the part. ; ordrng 1 WB27X27172 (Board), states that autho needed"

The whole unit does not cool and the hisplay shows HI. I pulled it out and found the compressor and condenser fan not working. I unplugged the fridge and plugged it back in. The compressor started and the fan started. It started to cool. The customer said they have done that before and it works for a while. I think it needs the rear board. I called Danby to ask if it just needs the board but they dont answer and tell us to leave a message. Please research the part and contact the customer. ; saved tckt

Customers complaint E IF ERROR CODE FOR ICEMAKER FAN MOTOR. Customer explained will get the error randomly through out the day. Remove ed the evap cover and found the fan seized will need new fan motor or assembly. I found there is a service bulletin on this for this issue. Added photos of service bulletin. Customer is up set because only 2 years old. He said he is calling LG to see what they have to say. I explained we cant call or talk on your behalf. They say needs new fan motor and fan bracket. The one they call for subs to a different one. Not sure if we can use that sub or need the one called for from bulletin. ABA74248414 bracket assembly EAU63923603 motor Labor should be set at L14. Will need to call customer back once we have an answer on the bracket and a quote; saved tckt

"Customer complaint is, NOT WORKING, PF error. Inspected and tested. Dishwasher is in rough shape. The tub is warped on the top and both sides and the door doesnt line up and seal properly. Both door gaskets have failed and are falling apart. The right door spring is broken. The circulation pump is loud and its not washing well and its giving a PF error. Because of the warped tub, dishwasher needs to be replaced. ; saved tckt"

"Unit leaking. Found unit not mounted pulled unit out and ran unit and found water leaking from the case break and the drain hose. Its inserted properly. Will need hose and case break. installed both parts. Once installed tested multiple times. No leaks reassembled unit tested another time and unit is working properly. Property manager didnt answer for payment once repair was completed. ; saved tckt , states that autho needed"

Customers complaint no cold water. Unit has SmartHQ. Pulled up error codes and nothing. Put unit in test mode. Ran cold water valve and it was hot. Ran hot water valve and it was cold. Explained to customer the hoses are on the wrong valves. Swapped hoses. Tested multiple times to make sure no leaks occur. Everything working properly.

The double built oven upper oven does not heat and gives code. I verified its not heating. I removed the panel and found one of the connectors was burnt. I repaired the connector and now its heating up good.

Unit trips breaker when plugging in. Seams like something is shortening out. Started slowly unplugging and figuring out is causing it. Isolated to the igniter or valve. Found a pinched wire on the valve. Cut out where the wire was separating. Repaired wire. Reassembled unit. Tested and now unit is working properly.

"Customer complaint is, DISPENSER NOT WORKING. Inspected and tested. FF compartment temperature is 39F and freezer is 2F. Ice maker is making ice, just not dispensing ice or water. The display is just flashing zeros. I removed the RFID water filter board and it visible looks good. Theres nothing in the tech sheet about what the flashing zeros mean. I called GE Techline and waited on hold for over 30 minutes and he helped me check somethings and we found a loose connection at the bottom of the door hinge. After messing with it the display is now working and ice and water are dispensing. He said to replace the door if they continue to have problems. I called the manager and updated him."

"Customer complaint is, SOMETIMES IT TRIPS THE CIRCUIT BREAKER BY ITSELF OR WHEN DOOR IS OPENING DOES THE SAME. Inspected and tested. Found the door switches are flaky and the holder is wore out. Customer approved repairs. Installed new holder and 3 switches. Tested and microwave is working great. Microwave is now fixed.

When the dryer runs it vibrates. I found the Dryer blower wheels packed full of lint. I vacuumed all the lint out of the blower wheel and all the dryer sounds better. I leveled the washer and dryer.

The complaint is the whole unit is not cooling. I found the compressor is trying to start but it keeps buzzing. I found the start relay has failed. I replaced the relay device. The compressor started up and is cooling good. I advised if it happens again it would need a compressor.

I verified the wash pump is bad. Its locked up and wont start. I replaced the wash pump. Now it fills and washes good. I reset the control board.

"Customer just wanted the gas valve replaced not the spark module and electrodes. Replaced gas valve, tested and both burners come on fully. Oven heats and is working good."

Replaced bad heater assembly. Put into forced defrost. Ran it again after taking it out of defrost and now it no longer beeps. Everything running great now.

"Customer complaint is, LCD PANEL LIGHTS ARE BLINKING & IT WONT START. Inspected and tested. Found when you open and shut the door the display flashes. I removed the bottom toe kick panel and found the white hardwired power cable is caught in the door spring so it broke the black wire. I had to cut out about 8 inches and rewire at the junction box. Tested and dishwasher is working great. Dishwasher is now fixed."

Customers complaint unit leaking. Pulled unit out on protective mat. Removed back cover to test for leaks. After filling and draining we found water leaking from drain in the wall. Will need a plumber. Inspected the unit otherwise. Its working properly. The bearings are getting loud.

"Replaced the parts GE said to do to solve the moisture build up on inside wall divider of freezer and refrigerator. Evaporator thermistor, refrigerator thermistor, rusted out drain pan, evaporator fan assembly. Customer will keep an eye on it. Refrigerator is working good."

Making a squealing sound. Replaced two bad support rollers. Vacuumed out dryer and cleaned up pully shaft and roller shafts. Now everything runs nice and quiet. Runs great. Thought it needed a new pully but pully was great.

Found that the igniter is open and not glowing to turn on gas. Customer approved estimate. Replaced igniter and oven preheated to 350. Oven is heating and working good.

Ran dryer and checked steam function and did not find anything concerning.

The customer said the oven takes long time to heat and they get a gas smell. I found the bake ignitor is weak and takes a long time to heat. The bake ignitor was only drawing 2.5 amps. I quoted for the repair then replaced the bake ignitor. Now it heats faster and no gas smell.

"Water softener in house was installed in reverse, so resin flowed through the pipes in the house. The dishwasher and fridge are on a reverse osmosis system, which appears to have prevented the resin from affecting these two appliances. I ran this dishwasher, and timed the fill into the dishwasher at the beginning of the cycle. It filled in the standard amount of time. No film present on dishes or inside dishwasher. Water is spraying and circulating strong. Drains great. Inspected under the dishwasher and no evidence of damage. Everything checks out good."

"Water softener was installed in reverse, so resin flowed throughout the plumbing. After thoroughly inspecting fridge, I can find no damage from this mistake since fortunately the fridge is connected to reverse osmosis. I disconnected the inlet waterline from the fridge and tested the water in the valve which has no resin, and the valve is clean. All water first enters the fridge via the valve, so this was good to find. I also turned on the waterline when it was disconnected from the valve and ran water through it, and it had good clean water pressure. Dispensed some glasses of water from dispenser in door and water is clear and flows excellent."

"E8 error to which is displayed on the display ever since this customer returned from vacation in Detroit. Also, since then, the icemaker has not worked. Also, bottom drawer is sort of hard to open. Found stretched out door cables. Removed those. Also, replaced the PCB and the icemaker. Took the icemaker through service mode and made sure its on. Works great now."

Icemaker broke. Arm broke right off. Replaced bad Icemaker. Cycled it and made sure its on. Works great now.

Customer said it makes a loud buzzing/vibration sound 2-3 times though out cycle. I tested for over 30 minutes and didnt hear much of anything abnormal. Ran diagnostics and tested ever component and no abnormal nosies. I did find that both upper and lower spray arms were clogged with food/popcorn kernels and were not rotating. I suspect that clogged spray arms could cause them to vibrate making the noises since it wasnt spinning.Now that spray arms are clean customer will use as normal and call back if problem persists.DIshwasher is working good.

Customers complaint unit leaking. Installed parts. Tested unit and its working great

Went to install new switch. Once installed tested and found only the little burner light. turned on with using. Also only would light up the little burner. The he switch is correct just is bad out of the package. Reorder and reschedule ; ordrng 1 Wb24x25014 (Switch)

Apartment with no unit information. Cannot get ahold of any contact to let us know.Waited 20 minutes. Will need to be rescheduled.; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)

"Customer complaint is, CODE F90 AND DOOR LOCK DOESNT WORK. Inspected and tested. Found the door lock is in the locked position. I cant get it to cycle open. Im ordering a new door lock motor. Installed new door lock motor assembly and tested. Door unlocked and oven is heating and responding and no more errors. Range is now fixed. Please collect. ; saved tckt , states that autho needed"

"LEFT VOICE MAIL, knocked multiple times. SENT HEADS UPS. NO ANSWER. WILL NEED TO RESCHEDULE. WE NEED TO GET PAID FOR VISIT OUT!! ; states that autho needed"

"The customer complaints are, the dishwasher leaks from the left corner of the door, the dishes dont clean well and not all the soap washes out the soap cup and the lock icon is stuck on the display. I found the control panel is not locked and the buttons do respond when pushed. I looks like there is some moisture stuck in the display. I added a picture. The lower spray arm has stuff stuck in the spray arm and that clogging up the small holes. I found a round piece of rubber in the filter basket. That could have been restricting the water pressure. I found a dent on the edge of the inner door. That dents looks to be causing the water leak. The water is able to leak past the gasket where it seals against the inner door. I was able to clean the basket and the lower spray arm. The dishwasher will need the inner door, the door seal and the user interface control display. Please check pictures and find the parts needed them contact the customer with a quote. I did try holding the temp 3 waves lines but the lock light is still on. Also the customer showed me the lower rack is missing parts? And the silverware basket doesnt really anywhere well. I also found the upper rack is missing a spray arm. I added more pictures. ; snapped 8 QuickPics, states that autho needed"

"Motor is running louder when in high speed spin. Also the shocks (4 of them) need to replace and belt.Motor, shocks, belt.Dryer is stacked and would need to pull out of closet and take off dryer. Please find parts and charge extra labor for 2 guys to pull out of closet to do repair. Please quote accordingly.; saved tckt"

The washer does not drain. I found the washer is getting 120 out the board but no voltage to the drain pump. I tested the ohms of the drain pump from the board harness and its 0. I get 25 ohms at the motor. I found the harness is bad somewhere. I quoted for the repair and I ordering the harness. ; ordrd 1 WH19X27495 (HARNESS)

"Not draining. Found debris stuck in air gap. Then when running, it kept running drain pump: found water had flooded underneath. Dried that out. Runs great now."

"Customer complaint is, NO HEAT. Inspected and tested. Found the thermal fuse was blown. Customer approved repairs. Installed new thermal fuse and vacuumed out inside of dryer. Tested and dryer is heating, but is getting to hot and I had to shut it down when it got to 260F. I disconnected vent and now heat is cycling perfectly between 210F and 105F and airflow on back of dryer is 30mph. It vents out the second story, so I cant check airflow on outside of house. The vent is the problem. I advised customer to not use dryer until the vent gets cleaned.

The complaint was the door lock icon was on the display and oven was running. When I arrived the customer turned the power back on. The upper oven door was not closed all the way and the door lock was trying to unlock. It was unable to move the lock to the unlock position because the door was pushing on the door lock strike. I held the door switch in and it moved to the door unlocked position. I started the bake and let the oven heat to 350 then pressed cancel. There are no faults and the oven is working good.

The dryer motor does not start when start is pressed. We removed the main board and found the motor relay solder joint was bad. We repaired the motor relay. Now the dryer starts and tumbles. No other issues found.

We found water leaking from the wash pump seal. We also found that water is leaking from the side of the tub. It will need a wash pump and run to fix it. I advised the customer its not worth fixing the tub. He would be better off replacing the dishwasher.

The washer was filling very slow with hot and cold water. It needs a new water valve. The customer got a new water valve. I installed the water valve the customer got from Dey. I advised the customer we cannot warranty the part. Now the washer is filling really good.

"Today we replaced the inner door with seal, door seal, user interface, wash pump and heating element we ran the dishwasher and do no leaks. No other issues found."

One of the drum baffles fell off. I added new screws to the baffle so it does not come off.

"Dead. Found a bad thermal cut out. Replaced fuse and vacuumed a ton of lint out of dryer. Also found a broken lint screen. Shipped new one to customer, otherwise lint gets into dryer. Also, fuse got knocked out due to a venting issue. Did a vent cleaning. Runs and vents great now.

New install. Installed Samsung dishwasher. Tested and dishwasher is running and working good.

Display was dead. Checked voltage at outlet. That was good. Next moved to the junction box that was good. Pulled unit out and tested at the board. I found getting voltage to display. Unplugged reassembled and it started working. Quoted for new display. They will see if fails again.

Replaced control board and igniter. Tested and oven is heating and working good.

"Orange flames. Found a humidifier running by the cook top. Asked if he had other questions. He asked about the vent fan for it. He said smoke came up in the house one time. I used a ladder and climbed through a crawl space under the house, and found a number of gaps where the venting seams came together. I used vent tape to seal it all up.

Installed new limit thermostat from diagnosis. Once installed reassembled. Tested unit multiple times heating and tumbling correctly. Unit is heating properly also. Did recommend last time getting the vents cleaned. Cleaned inside the dryer and did a maintenance cleanup. Unit is now operating correctly.

"One complaint is that all their food freezes and its always too cold. When I got here it was set to the coldest setting. I asked her if they've tried it on a warmer setting and she said yes. Temp near the top of the fridge is 39. Told tenant they cant have food along back or itll freeze. Tested the damper, and it doesnt close when set to the warmest setting. Always stays open. Replaced thermo assembly. Also, tenant said the icemaker doesnt work. I showed her that the arm was pulled out. She said that happened yesterday. When they pulled a bag of ice out. But that should not have pulled the arm out. She said the arm has always been in, and it hasnt made ice. I put the arm in and within a minute it cycled and filled with water. Water dispenses nice and strong from the dispenser. Freezer is zero degrees. Runs great now.

"Dishwasher not draining. Found the drain pump had a rock in it, cleaned out debris, and made sure entire drain line was totally clean. Filled and drained the dishwasher 4 times after cleaning out drain pump and it drains great every time now."

"Icemaker not working. They used to get some water leaking when the Icemaker was on. I thawed out the old Icemaker and tried cycling it, and it got stuck part way through the cycle. Bad motor. Replaced Icemaker, adjusted the dispenser chute so that water wouldnt splash up over funnel, it filled great and no leaks.

"Customer complaint was the refrigerator was was not cooling. Removed shelfs and back cover found frost built up. Steamed the ice out. Customer approved the updated kit. Installed new sensor, heater, and drain kit. Tested making sure the heater worked.

"Customer complaint is, FROSTING UP IN FREEZER. Frost is accumulating by the ice dispenser chute and underneath the ice bucket. Inspected and tested. FF compartment temperature is 39F and freezer is 8F. The ice chute door is stuck open. I messed with it and then it shut. Now its opening and closing perfectly. Nothing is broken on it. I showed this to the customer and advised to keep an eye on it."

"Customer complaint is, ICE MAKER STOPPED WORKING MAKES NOISES. Inspected and tested. FF compartment temperature is 37F and freezer is -2F. I checked the wiring harness at the bottom hinge and all ice maker wires had continuity. The sensor is just hanging from the bottom of the ice maker and the tray is breaking. Customer approved repairs. Installed new ice maker and tested. Ice maker cycled and filled with water. Ice maker is now fixed."

Tenant said melted a plastic ware and doesnt think water is getting in. Hooked up SmartHQ. No errors ran unit found the motor would try to kick on but wouldnt actually wash. Went in test mode tested all features motor isnt kicking on. Getting 120 to the motor. Needs new motor. ; ordrng 1 WD49X23781 (MOTOR MECHANISM TALL TUB)

They had the breaker pop and then the bake and broil stopped working. I found a smoked control board. I cant find the part number. DW could you try and find it and call customer with quote if you do?; saved tckt

E84 error. Checked everything in service bulletin. Either needs new inverter board or PCB or both. Gave customer ballpark quote for each option. They said if the inverter board is available theyd like to maybe try that. Can you see if thats available? And call them? ; saved tckt

Found that the dishwasher motor is bad. Just humming and not spraying water. Customer approved estimate. I picked up part and replaced sump assembly. Tested and dishwasher is running and working good.; ordrd 1 WPW10605058 (Sump assembly)

"Dishwasher wont turn on. It has power going to control board as LED light is on but no power is going out. But is having some weird power issues, i did get spikes of power to user interface. Ordering that part as well, incase but only quoted for the control board.User interface panel assembly AGL75675203; Control board AGM76429511; schdld next appmnt for 11/21 TUE !"

Customer says unit not cooling properly. Fresh food was at 36 which is fine. Im getting an issue with the freezer. So hooked up SmartHQ. Had codes for warmer temps and 3 way valve error. Put unit in test mode was able to change the position of the valve and is operating correctly. Try to start compressor and it wont its stuck. Can hear the compressor shake and act up but never runs properly. Will need a new inverter WR55X36435Dana is sourcing a inverter. Will need to update customer with time frame. ; states that autho needed

"When I got here there was a new range installed. They had moved the problematic range to the garage. There were no notes on this or parts listed but I had the parts. I assumed that it was covered by warener stallion or Beko. I went ahead the replaced parts but since there is no 220V in garage I cant test it.Customer is not happy with whole sistuation and bought a new one and will list the one I replaced parts on for sale.I dont know if there is any balance due and it only took me 15 minutes since it was just part and I didnt test it. No notes on billing and customer is very unhappy.I guess send to Phil and see what we want to do with this?; saved tckt , states that autho needed"

"Replaced bad spark module but no matter how I had terminals connected, it would only spark one side, not both. Confirmed that both ignitors spark. Needs new switch harness for the burner controls. DW can you try and find one and quote RPM for both that and the spark module and see what they want to do? Before only one knob would cause a spark to happen and that was sporadic. Now two knobs will cause the ignitors to spark. Ill need a double slot when I come back. ; saved tckt"

"Squealing. Found two bad support rollers. Replaced them and cleaned and oiled shafts. Cleaned and greased pully/ vacuumed out dryer: runs great now.

"Customer started the lower oven was not starting. Remove racks, lower covers found the bake ignitor was not operating correctly. Quoted the customer repair customer approved. Install new bake ignitor cycled and tested oven now starts and is operating correctly.

"The dishwasher just drains but never stops to fill. It was getting all the pressure sensor faults. We quoted for the sensor part. We replaced the pressure sensor and cleaned out the drain hose. We then ran the diagnostic test. Now the dishwasher will drain then stops and fills and runs a cycle. All working good now.

Found that the freezer evaporator drain was clogged and froze the line so it woulf then defrost onto bottom of freezer and then eventually leak onto floor. I defrosted drain line and cleaned ice build up. Now drains correctly and no longer leaks. Refrigerator is working good.

Found that the dishwasher latch was tripped without door being shut so the dishwasher thought the door was shut and the touch pad is unresponsive. I showed customer how to reset it.

Unit leaking water on second load. I found where one of the clips on the hose for the recirculation pump was loose and leaking. Its a pinch style. Replace hose clamp and checked the others. Now unit is working properly without leaks

Unit giving F9 code. Checked SmartHQ. Cant hook up but looked up tech sheet found its for the cooling fan or thermostats. Pulled unit out. Tested the high limit cut out. That was good. Next checked the sail switch. Found the switch is good. But it was a little sticky. Tested unit found the sail switch isnt working. Cleaned the switch off. Has dust built up. Tested oven multiple times switch engages every time.

Found that the dryer sound was from the vent being split and air escaping making whistling sound. Also the outside vent flap plastic was broken and open. Customer approved estimate to replace some sections of vent and the outside flap. Tested and dryer now vents outside and no whistling sound. Dryer is running and cycling heat normally.