Service History 15 - Omega Force Appliance Repair

We serviced a

WHIRLPOOL DISHWASHER

Model WDTA50SAHZ0

Near Ramsey, MN 55303

Phillip

Job Details: 03/05/2024

"The customer said the dishwasher was leaking from the front right corner. I found the lower spray arm was sitting on top and not attached correctly. I inspected the lower spray arm for any cracks and splits and it was OK. I reinstalled the spray and ran the dishwasher for more than a half an hour. The dishwasher is not leaking, but there was over sudsing. Advise the customer to use a different soap and I raise the front right corner."

We serviced a

BEKO DISHWASHER

Model 7620809580

Near Saint Paul, MN 55119

Hyrum

Job Details: 03/05/2024

"The drain hose for this machine had clogged and made the machine overflow again. Cleared the drain hose and instructed the customer on clearing the filter. Also mentioned the size of the tubing that the drain hose was connected to might be too small. After I cleaned out that drain hose, I opened up the bottom and dried it up under there. put everything back together and ran it for a few minutes. Everything looks good now."

We serviced a

GE REFRIGERATOR

Model GSS25GMHJCES

Near Maple Grove, MN 55369

Phillip

Job Details: 03/05/2024

The filter manifold was defective. I replaced the filter manifold. No leaks and the water comes out better.

We serviced a

GE WASHER

Model GTW465ASN0WW

Near Saint Paul, MN 55116

Hyrum

Job Details: 03/05/2024

Customer states it wont go all the way through the spin cycle. Start the machine let it run and even empty. It didnt get up to full speed before trying to rebound. Opened up the cover and checked the belt and it was really worn down. Ordered and picked up a new belt from dey. Installed and tested. Machine seems to be working right now.

We serviced a

WHIRLPOOL DRYER

Model GGW9250PW3

Near Apple Valley, MN 55124

Delton

Job Details: 03/05/2024

Found that the idler pulley is worn and making squealing noises. Customer approved estimate. Replaced idler pulley and cleaned out inside dryer of lint build up. Tested and dryer now runs quiet and is working good.

We serviced a

BOSCH OTHER

Model TKN68E75UC/04

Near Shakopee, MN 55379

Delton

Job Details: 03/05/2024

"Replaced tray, tested and coffee maker starts and brewed a cup of coffee. Machine is working good."

We serviced a

FISHER PAYKEL++ DISHWASHER

Model DD603I

Near Plymouth, MN 55447

Phillip

Job Details: 03/05/2024

Today I replaced all the karts that were ordered and sent. Both dishwashers are working and found no water leaking.

We serviced a

AMANA DRYER

Model Ned4600yq1

Near Saint Joseph, MN 56374

Brandon

Job Details: 03/05/2024

Customer states the dryer would not start. Tested found the fuse on the blower housing blown. Replaced fuse and replaced fuse and t-stat. Cycled and tested found the element was shorted out and running when the timer was turned to a time. Replaced the heater element. Cycled and tested the unit now turns on and the heater is cycling as it should

We serviced a

MAYTAG WASHER

Model MVWX655DW2

Near Ramsey, MN 55303

Matt

Job Details: 03/05/2024

"Cut out old agitator and installed new gearcase, splutch, drive hub, agitator and screw. Tested and washer is working great. Washer is now fixed."

We serviced a

KITCHENAID DISHWASHER

Model KDPM604KPS0

Near Hastings, MN 55033

Delton

Job Details: 03/05/2024

"Replaced motor/sump assembly and control board. Tested and no error, all functions are working. Dishwasher is working good."

We serviced a

ASKO++ DISHWASHER

Model 107323271

Near Wayzata, MN 55391

Nate

Job Details: 03/05/2024

"Installed new water valve, checked for leaks. Works good, job complete."

We serviced a

ASKO++ DISHWASHER

Model DFI675XXL.U

Near Minneapolis, MN 55424

Nate

Job Details: 03/05/2024

Screws came out. We found that holes were stripped from previous installers. We used longer screws and a bolt and nut and now its secure and latches great. Tried opening and closing 10 times. Closed and latches great every time.

We serviced a

SAMSUNG REFRIGERATOR

Model RF32FMQDBSR/AA

Near St. Cloud, MN 56301

Brandon

Job Details: 03/05/2024

Customer states there is water leaking in the refrigerator when trying to dispense water. Found the water tank in the filter housing cracked. Customer approved the quote. If the parts can be sourced the customer will repair. Case water tank DA61-07210AFilter housing DA97-12669B; saved tckt

We serviced a

GE DRYER

Model DPSE810GG8WT

Near Loretto, MN 55357

Adam

Job Details: 03/05/2024

"Customers complaint is making loud noise and squealing noise. Disassembled unit found that the front bearing is completely destroyed. Also, the rear bearing is going out. Quoted the customer for both bearings. Customer approved rescheduled for Friday.; ordrng 1 WE25M40DNS (REAR BEARING KIT), used 1 WE49X20697 (BEARING ARM - DRUM TOP FRONT W/FELTS) from stock"

We serviced a

BOSCH DISHWASHER

Model SHP65T55UC/02

Near North Oaks, MN 55127

Hyrum

Job Details: 03/05/2024

Customer stated its leaking and giving an e15 code. Customer had machine disassembled at this time. Turned machine on and ran it and discovered a leak from the diverter seal. Ordered part form Marcone and will return Friday.; ordrng 1 00751950 (Diverted assm)

We serviced a

GE DRYER

Model GTD42GASJ2WW

Near Hopkins, MN 55305

Adam

Job Details: 03/05/2024

Unit was making loud noise during tumble. Removed the front and found the front bearing assembly was pretty much destroyed. All the slides were gone quoted for new bearing assembly ran and got the part for the customer install installed and now working properly.; ordrng 1 WE03X25576 (BEARING ARM - DRUM TOP FRONT W/FELTS)

We serviced a

SAMSUNG REFRIGERATOR

Model RF263BEAESG/AA

Near Saint Michael, MN 55376

Matt

Job Details: 03/05/2024

THE ICE MACHINE WILL NOT DROPP THE ICE. THE TRAY IS FULL AND ACTUALLY BENDING FROM THE ICE EXPANDING. The bottom of the ice maker is melted. Can someone find this ice maker kit and call and give customer quote please and if theres no kit then quote for a new ice maker and sealing the ice room. Please schedule me 2 hours if I go back. They shouldnt need to unplug refrigerator before I go back. ; saved tckt

We serviced a

DANBY ICEMAKER++

Model DIM32D1BSSPR

Near Minneapolis, MN 55449

Hyrum

Job Details: 03/05/2024

"Temp sensor Dg8-23-1Main control dg3-103-1Overlay dg20-219Customer states that it runs for a couple hours and then stops making ice and has an error code. Call Danby tech-support and they stated that the error code is for the reservoir not being full. Confirmed that the float valve is operating correctly and the reservoir does stay full. They said that the failure is likely a board and temperature sensor. They said this is a common failure. They gave me the parts for the overlay control and temperature sensor and these are the parts that will need to be replaced. They also said it could be an intermittent problem with the pump, but this is unlikely. I asked the customer to keep an eye on it to see if there are any times where the pump would stop running intermittently but not have an error code yet. please find these parts and call the customer with a quote and schedule for when we can come back. ; saved tckt"

We serviced a

MAYTAG DRYER

Model MED6000AW0

Near Apple Valley, MN 55124

Delton

Job Details: 03/05/2024

"Ordinal part was incorrect part and not the whole housing. I picked up the whole housing assembly part. Replaced part, tested and lint trap now slides in and out easily. Dryer is heating and working good.; ordrd 1 W10906551 (Lint trap housing)"

We serviced a

LG REFRIGERATOR

Model LRFWS2906D.ASBCNA0

Near St. Cloud, MN 56303

Brandon

Job Details: 03/05/2024

"Customer states the unit is not cooling correctly.Found the fresh food compartment warm the freezer is cold and everything in it is frozen. The unit has a FFE code. Removed the drawer and the back cover, checked the evaporator and it has a normal frost pattern. Checked the fan for ice or and thing obstructing it. Fan blade spins smoothy. Ordered part ; ordrd 1 AEB73764526 (Grill assembly)"

We serviced a

BOSCH DISHWASHER

Model SHPM65Z55N/20

Near Maple Grove, MN 55311

Matt

Job Details: 03/05/2024

"NOT POWERING ON. Outlet has power. I found the UI board is really corroded at one of the connectors. Installed new UI board and tested. Its still dead. This is going to need a new main board. It looks like Jared ordered one, but I dont have it. Can someone see if its been ordered, and if not order one and reschedule the customer. Part number 12028528. I need 2 hours on my return trip. ; saved tckt"

We serviced a

ASKO++ DISHWASHER

Model D5534

Near Saint Paul, MN 55105

Hyrum

Job Details: 03/05/2024

640393 Drain tube assm with orings. Customer states it will leak a bunch of water suddenly and few mins into the cycle.Drain tube assm is cracked and leaking. Need to replace this part with OEM part. Please order this part and quote customer for repair. ; saved tckt

We serviced a

BOSCH DISHWASHER

Model SHP865ZD5N/01

Near Saint Paul, MN 55102

Hyrum

Job Details: 03/04/2024

Customer states its not dissolving soap and its not washing dishes very well. Started machine and discovered. It was barely any water in. Trace the cause of this issue to the fill valve. Went today and picked up the replacement part. Replace the fill valve and tested. Machine works a lot better now that its feeling properly. Everything looks great.

We serviced a

GE MICROWAVE

Model JVM1650SH05

Near Sartell, MN 56377

Brandon

Job Details: 03/04/2024

"Cycled and tested the unit, the unit was not heating. Disassembled, removed and installed new mag tube. Cycled and tested the unit is now heating. Put back together and mounted it back above the stove."

We serviced a

LG DRYER

Model DLE0442W

Near Champlin, MN 55316

Phillip

Job Details: 03/04/2024

The dryer had poor air flow. I installed 2 new elbows to the dryer. The air flow outside was poor. I cleaned the dryer duct and the inside of the dryer. All tested good.

We serviced a

KITCHENAID DISHWASHER

Model KDFE204KPS0

Near Ramsey, MN 55303

Matt

Job Details: 03/04/2024

"LEAKING UNDER THE FLOOR - UNIT IS PULLED OUT TO DRY OUT FLOOR. Sounds like it was leaking from the door and clean light was blinking and customer saw lots of suds in dishwasher. I turned breaker on and drain pump is running. Found water in the float pan underneath. Removed water and started a heavy cycle and after about 5 minutes I opened the door and its full of soap suds. I showed this to the customer and advised that its leaking from excessive soap suds in dishwasher. I ran dishwasher for over 35 minutes and never saw it leak, but theres still lots of suds. I told customer to run a cleaner through dishwasher and if it keeps sudsing up to try a different soap. Afterwards I found out customer probably got dish soap in the dishwasher right before it leaked."

We serviced a

GE REFRIGERATOR

Model PYE22KSKJSS

Near Eden Prairie, MN 55347

Adam

Job Details: 03/04/2024

Explained to customer do not use turbo or turbo freeze and let it regulate temperature is now that its been updated. Went through test mode made sure everythings running properly. Everything is working the way it needs to and no error codes."

We serviced a

BOSCH DISHWASHER

Model SHP65T55UC/07

Near Victoria, MN 55386

Adam

Job Details: 03/04/2024

Customer is complaint is unit not draining properly. They already had all the water bailed out of it check pump nothing was caught in the pump so I filled it for water to drain and found the pump sounded good so took off the drain hose to the food disposal and found that the food disposal still had its plug-in there. removed the plug, redid high loop for the drain hose and now unit is draining properly properly.

We serviced a

BOSCH DISHWASHER

Model BSHDW

Near Saint Paul, MN 55108

Hyrum

Job Details: 03/04/2024

"Top basket had come off the rail, part of the way on one side and wasnt pushing all the way back, preventing the door from closing. readjusted the rack and made sure it slighted on the rails back-and-forth. Nice and easy. After that the door was opening and closing perfectly. Ran the machine through a quick cycle and it did great. Everything looks to be functioning properly now."

We serviced a

GE DISHWASHER

Model GDF630PSM3SS

Near Eagan, MN 55122

Delton

Job Details: 03/04/2024

Has GE issue to where dishwasher wont power on unless power cycling 10-20 times. Software update should fix this. Customer approved. Software update successful. Tested and all functions are working good.

We serviced a

WHIRLPOOL DRYER

Model WGD95HEXW0

Near Minneapolis, MN 55448

Matt

Job Details: 03/04/2024

"WON'T START WHEN START BUTTON IS PUSHED. Found the belt was shredded. Customer approved repairs. Installed new rebuild kit and vacuumed out inside of dryer. Tested and dryer is working great. Dryer is now fixed.

We serviced a

LG REFRIGERATOR

Model LRMDS3006D/01

Near Elk River, MN 55330

Matt

Job Details: 03/04/2024

FREEZER ICE MAKER MAKES LOUD NOISES WHEN DROPPING ICE INTO TRAY. Installed new craft ice maker and main board supplied by warranty and tested. Ice maker cycled and filled with water. Ice maker is now fixed.

We serviced a

SAMSUNG DISHWASHER

Model DW80R9950US /AA

Near Blaine, MN 55434

Phillip

Job Details: 03/04/2024

"The dishwasher is hard wired to a gfi in the basement. I added a picture. After about 1 hour the gfi will trip. I hooked up hass, the vane error and drain error were stored. I ran a diagnostic test and it passed. In the manual test the vane will moved forward and back but does not stop. It may need the vane assembly. The customer will try a new gfi first."

We serviced a

LG REFRIGERATOR

Model LFXS29766S/01

Near Minneapolis, MN 55443

Phillip

Job Details: 03/04/2024

The refrigerator was not running and not cooling. When I arrived I found the fridge was plugged in and the error FF was on the display. After inspection I found the board was replaced with the wrong main board. The previous company cut the main harness and put on spade connectors to make it work. Then forced plugs in the wrong spot. I had to use the new board that was sent and do some soldering to make it work again. Now all the fans work and the compressor runs. I found the compressor has failed. I replaced the compressor and recharged it with 5.1 ounces of refrigerant.

We serviced a

GE COOKTOP++

Model PP9830SJ1SS

Near Eagan, MN 55123

Delton

Job Details: 03/04/2024

Fan switch stem broke off. Replaced fan switch. Tested and fan now turns on and runs. Cooktop heats and fan works. Cooktop is working good.

We serviced a

SPEED QUEEN WASHER

Model AWNE9RSN115TW01

Near Hopkins, MN 55343

Nate

Job Details: 03/04/2024

Replaced bad lid locks. Works great now.

We serviced a

MAGIC CHEF DRYER

Model CYG3005AWW

Near Robbinsdale, MN 55422

Phillip

Job Details: 03/04/2024

"The blower wheel had stripped and was loose. I replaced the motor, blower wheel and rear rollers. The dryer runs and heats good."

We serviced a

FRIGIDAIRE MICROWAVE

Model FFMV1645TS

Near Apple Valley, MN 55124

Delton

Job Details: 03/04/2024

"Replaced choke kit, tested and microwave is heating and working good."

We serviced a

BEKO DRYER STACKED++

Model BDV7200X

Near Minneapolis, MN 55407

Nate

Job Details: 03/04/2024

Making a rumbling sound. Found two dryer sheets stuck in blower wheel. Cleaned that and lint out. Runs great now.

We serviced a

LIEBHERR++ REFRIGERATOR

Model CS2061

Near Minneapolis, MN 55419

Nate

Job Details: 03/04/2024

"Replaced icemaker, tested. Checks good."

We serviced a

MAYTAG DRYER

Model mdg5500aww

Near Minneapolis, MN 55417

Nate

Job Details: 03/04/2024

"Felt seal on bulkhead was worn through causing a scraping sound. Replaced part, checks good."

We serviced a

DACOR++ RANGE

Model ERD30

Near Saint Paul, MN 55118

Nate

Job Details: 03/04/2024

Replaced bad bake element. It works great now.

We serviced a

WHIRLPOOL WASHER

Model LSQ8543JQ0

Near Minneapolis, MN 55426

Nate

Job Details: 03/04/2024

"Washer stopped with tub full of water. It was able to drain, but the transmission is starting to leak oil. Needs transmission and clutch and coupling. Estimate is attached. Customer will talk it over with their spouse and call us tomorrow to let us know if they want to do the repair or not. ; saved tckt"

We serviced a

GE RANGE

Model JB655SK7SS

Near Sauk Rapids, MN 56379

Brandon

Job Details: 03/04/2024

"Returned, installed new board, plugged in. Found the stove was not getting power. One side of the breaker was not putting out 120 volts. The son said that he will have someone come and updated the wiring breaker and plug, I asked him not to plug it in until it is rewired then to call us and get on the schedule so the board can be programmed. ; states that autho needed"

We serviced a

MAYTAG WASHER

Model MVWB835DC3

Near Waite Park, MN 56387

Brandon

Job Details: 03/04/2024

"Customer states the unit has an F5 code. Plugged the unit in and it is trying to cycled the lid lock, and just keeps flashing the F5 code, removed the top cover and removed the lid lock, made sure there was no debris in the mechanism. Unplugged the lid lid lock and checked the codes all F5 code for the lid lock. Customer approved a new lid lock. ; ordrd 1 W10861642 (Lid lock switch)"

We serviced a

BERTAZZONI** VENT HOOD

Model KG48X

Near Wayzata, MN 55391

Adam

Job Details: 03/04/2024

"Customer is complaint is unit showing a then whatever the fan speed is. Nate was there before talk to Techline. They thought it was a vent air code and-ordered a board. Installed control board tested still given the error. Not getting service at customers house had to leave and call Techline when I spoke to Techline they said it was not a error code and that the unit is running properly. Either way, if it is a error code or a venting code. I am unable to repair. I did run unit without grease traps, and it was still giving the air code.; states that autho needed"

We serviced a

HISENSE REFRIGERATOR

Model HBM17158SS

Near Shakopee, MN 55379

Adam

Job Details: 03/04/2024

"Installed parts from last diagnosis, so top hinge bottom hinge. This was for the other side so I had to swap over the handle. Also everything worked out really good now is sealing properly. Only thing that we didnt quote for was a cap on the top hinge because its the opposite side customer would just like an idea how much support would be and then we could ship it to them and they can install themselves Add a photo of where it would be"

We serviced a

LG REFRIGERATOR

Model LFXS26973S/04

Near Maple Grove, MN 55369

Matt

Job Details: 03/04/2024

"SOUNDS LIKE SOMEONE IS RUNNING A CONCRETE DRILL, 18 MONTHS OLD. 48 DEGREES IN FRESH FOOD. Customer had refrigerator unplugged and completely defrosted when I got here. The evaporator fan motor has failed. Quoted customer $500. to install new evaporator cover assembly with fans. Customer approved repair. Part on order. ; ordrd 1 AEB73764534 (EVAP FAN MOTOR SEE MOTOR)"

We serviced a

SPEED QUEEN DRYER

Model ADEE9RYS177TW01

Near Minneapolis, MN 55439

Adam

Job Details: 03/04/2024

"Complaint is unit will just run on its own and then give the error code. I found when I plugged it in that as soon as you shut the door, the unit would start running. Removed lower to panel removed control board. Didnt find any burnt up relays, tapped on all the relays reassembled units were properly and then it got stuck again unit needs a new control board. Homeowners werent there but a guy was there cleaning and said that they would want it done and to order the parts. I did order parts and put them on the schedule left voicemail for Eric to give us a call back and let us know if you for surely wants to do it. Also let him know it might be under warranty. It be worth calling to see if they could get it covered or reimbursed after we did the repair. Unit is in a tight spot. I will have to pull washer out to reconnect the dryer after someone pulled out the dryer and it vented out the side and a cabinet and no way to access it. Add photos to show.; ordrd 1 D518191 (Output board)"

We serviced a

WHIRLPOOL RANGE

Model RF315PXPT1

Near Maplewood, MN 55109

Hyrum

Job Details: 03/04/2024

"Customer states it made a loud pop and threw the breaker, and will do the same if they turn the breaker back on. Discovered a melted terminal block that was shorted to the case. Replaced terminal block and cord with parts from Dey. Tested machine and its working great now.; ordrng 1 WP9761958 (Term block), used 1 CORD-4PRONGRANGE (RC4-50-6 4 PRONG RANGE CORD) from stock"

We serviced a

BEKO RANGE

Model PRGR34550SS

Near Saint Paul, MN 55109

Hyrum

Job Details: 03/04/2024

"Replaced the failed gas valve and the main board. Tested the machine and the oven came on right away. Seems to be working great now.; saved tckt , states that autho needed"

We serviced a

LG REFRIGERATOR

Model LRFVC2406S/02

Near Cottage Grove, MN 55016

Delton

Job Details: 03/04/2024

No water coming though door or ice not being made. I checked wall water and there is a lot of pressure. I can hear valve activate but no water is being dispersed from the inlet water valve. There was some weird goo that sprayed out when i was testing water line to fridge. Needs new inlet water valve and also order dual door water valve incase.Cannot find inlet water valve assembly (see picture) please find that part quote customer.Dual water valve in door- MJX64471402Inlet water valve assembly - ?; saved tckt

We serviced a

SPEED QUEEN WASHER

Model AWN43RSN116TW01

Near Apple Valley, MN 55124

Delton

Job Details: 03/04/2024

"Replaced lid switch, tested and switch now locks and unlocks normally. I ran quick cycle and it completed but then soon after washer kept beeping and flashing wash<spin<lid lock 3 times.Tech support said that the bottom control board is bad. So now i will order that part and reschedule.Part# 204659P; ordrd 1 204659P (Bottom control board)"

We serviced a

GE DISHWASHER

Model GDT655SGJ2WW

Near Lakeville, MN 55044

Delton

Job Details: 03/04/2024

Found that it is leaking from diverter hose. Part comes as an assembly. Customer approved estimate. Ordering part and rescheduling.; ordrng 1 WD19X25278 (MOTOR/PUMP ASSM)

We serviced a

KITCHENAID DISHWASHER

Model KDTE334GPS0

Near Saint Paul, MN 55118

Nate

Job Details: 03/04/2024

"Rack adjusters broken and right metal rack rail is broken. Ordered parts, coming back Wednesday to install. ; used 1 WPW10546503 (ADJUSTER) from stock, ordrd 1 W11259786 (Right rail)"

We serviced a

LG RANGE

Model LSG4513ST

Near Saint Paul, MN 55104

Hyrum

Job Details: 03/01/2024

Customer states that since the last visit the convection fan has stopped working entirely. Replaced the convection fan with the part that I ordered. It seems to be working great. Let the machine preheat and had no issues at all. Everything looks great now.

We serviced a

BOSCH DISHWASHER

Model SHP865WG5N/11

Near Otsego, MN 55362

Matt

Job Details: 03/01/2024

"ERROR E25 WON'T COMPLETE CYCLE. Found standing water in the bottom of the dishwasher. I tried canceling and draining, but it didnt drain. I sucked water out through the drain hose and its clear. Found the drain pump cover was loose and there was a lot of junk in there. Cleaned it out and reattached the cover. Tested and dishwasher is draining great. I filled and drained dishwasher 4 times and its draining perfectly every time. Dishwasher is operating great now."

We serviced a

SPEED QUEEN WASHER

Model AWNE9RSN116TW01

Near Elk River, MN 55330

Matt

Job Details: 03/01/2024

ER LD ON WASHER. Found the lid lock assembly is broken and is just hanging there. Installed new lid lock kit and tested. Washer is working great. Washer is now fixed.

We serviced a

WHIRLPOOL DRYER

Model WGD4815EW0

Near Rogers, MN 55374

Matt

Job Details: 03/01/2024

"DRYER MAKES AN AWFUL SQUEELING NOISE FOR FIRST 5 MINUTES EVERYTIME IT IS RUN. Found the left rear roller is seizing up and squealing. Customer approved repair. Installed new rebuild kit and vacuumed out inside of dryer. Tested and dryer sounds great. Dryer is now fixed.

We serviced a

WHIRLPOOL MICROWAVE

Model WMH53321HZ-5

Near Hopkins, MN 55305

Adam

Job Details: 03/01/2024

Customer complaint is when opening door doesnt always read door open and sometimes doesnt read the door being closed. On arrival, it was working. Sounds like bad door switches. Remove switches found the switches are bad and faulty. Replaced all four and now units working properly

We serviced a

GE DRYER

Model GTX22GASK0WW

Near Maple Grove, MN 55311

Matt

Job Details: 03/01/2024

BREAKER KEEPS TRIPPING. Found the ignitor is burnt out. Installed new ignitor and tested. Dryer is heating great and cycling between 220F and 115F and not tripping breaker. Dryer is now fixed.

We serviced a

GE REFRIGERATOR

Model GSL25JFXBLB

Near Minneapolis, MN 55446

Matt

Job Details: 03/01/2024

NOT COOLING. Found the heating element had failed. Defrosted evaporator and installed new heating element. Refrigerator is now fixed.

We serviced a

SPEED QUEEN WASHER

Model AWNE9RSN115TW01

Near Maple Grove, MN 55369

Phillip

Job Details: 03/01/2024

Knocking noise in wash cycle. I verified the issue. Found bulletin that says to tighten the lower drive nut. I tightened the nut. I tested and sound is gone.

We serviced a

BOSCH REFRIGERATOR

Model B36CL81ENG/03

Near Lakeville, MN 55044

Delton

Job Details: 03/01/2024

Replaced water valve and ice maker. Tested and ice maker cycles and fills. I informed customer could take up to 24 hours for ice to be made.

We serviced a

GE REFRIGERATOR

Model GSS25GMHJCES

Near Maple Grove, MN 55369

Phillip

Job Details: 03/01/2024

Water pressure is slow. I verified water supply is good. Issue is with the filter or manifold. The customer will try a genuine GE filter.

We serviced a

KENMORE DRYER

Model 11060812990

Near Waite Park, MN 56387

Brandon

Job Details: 03/01/2024

"Customer states the unit runs and shuts off after a few minutes.Cycled and tested, while running the unit was very loud. Disassembled and found the motor is what was making the noise. Customer approved the new motor. Ended up needing a blower wheel as well, Replaced both. Cleaned and lubed the drum rollers, cycled and tested. The unit is now running with no noise."

We serviced a

ASKO++ DISHWASHER

Model DFI675XXL.U

Near Minneapolis, MN 55424

Nate

Job Details: 03/01/2024

"Replaced user interface and door latch, works good. Job complete."

We serviced a

SAMSUNG DISHWASHER

Model DW80R7061UG/AA

Near Coon Rapids, MN 55433

Phillip

Job Details: 03/01/2024

Water leaking into the base. I found the siphon break inlet cap was off and laying in the dishwasher. I put the cap back on and made sure its tight. No issues found.

We serviced a

GE WASHER

Model GTW465ASN2WW

Near Hastings, MN 55033

Delton

Job Details: 03/01/2024

"Replaced shifter, pulley, clutch. Tested and washer now shifts between agitate and spin. Washer is working good."

We serviced a

FISHER PAYKEL++ WASHER

Model WA37T26G

Near Minneapolis, MN 55424

Nate

Job Details: 03/01/2024

Washer hasnt been draining. We replaced bad drain pump and installed fuse kit. Runs and drains great now.

We serviced a

KENMORE DISHWASHER

Model 16879000

Near Sartell, MN 56377

Brandon

Job Details: 03/01/2024

"Customer states the dish washer is not draining.Cleaned out the drain hoses the unit still sounded like it struggled to pump the water out. Let customer know a price and the customer approved, pulled unit out and removed the drain pump got some debris out. Cleaned the drain lines again. Found the unit leaking on the left side where it fills with water. Informed the customer and the customer said it was ok to clean it off and put it back together. he is planning on replacing the unit soon"

We serviced a

LG REFRIGERATOR

Model LFC24770ST

Near Chanhassen, MN 55317

Adam

Job Details: 03/01/2024

Install new rollers now unit is working properly

We serviced a

AMANA REFRIGERATOR

Model ABB1924WEQ0

Near Saint Joseph, MN 56374

Brandon

Job Details: 03/01/2024

"Customer states the refrigerator is leaking water and is not as cold as it should be.Checked and found the freezer had water leaking down the door. Removed the drawer and door.Removed the back cover and steamed, found the drain clogged, cleaned out the drain. Streamed out the ice. Put back together, unit started cooling correctly ."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF560SEHZ00

Near Chanhassen, MN 55317

Adam

Job Details: 03/01/2024

Installed part. tested and everythings working properly

We serviced a

WHIRLPOOL DISHWASHER

Model WDT710PAHW1

Near West Lakeland Township, MN 55082

Hyrum

Job Details: 03/01/2024

Customer states it leaks after about a half hour of running. Turned it on let it run for about a half hour. Took off the door panel and saw that there was suds. Potentially coming over the tub lip door. Didnt see any leaks under the sump or anywhere else just from the front of the door. Pour a little oil in the dishwasher. Adjusted rinse aid setting. Tip the dishwasher back just a little bit.instructed customer on what to do if it leaks again. As of right now seems to be that weve resolved this issue.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ02

Near Blaine, MN 55449

Phillip

Job Details: 03/01/2024

The fridge ice maker failed and the freezer defrost thermostat failed. I replaced both parts today. I advised the customer to wait 3-24 hours for to make ice.

We serviced a

WHIRLPOOL WASHER

Model WTW7120HW0

Near Saint Paul, MN 55119

Delton

Job Details: 03/01/2024

"Replaced all listed parts, tested and washer fills, agitates, drains and spins. Washer is working good."

We serviced a

LG REFRIGERATOR

Model LFXS28566S

Near Waconia, MN 55387

Adam

Job Details: 03/01/2024

"Customer complaint is unit start getting warmer and warmer. Hooked up pressure gauges and found its reading as a restriction. Removed capillary tube from filter and found that was plugged right there. Removed filter dryer blasted nitrogen through it. Put new filter in vacuumed, held pressure under 300 ?m. Filled with cracked amount of Freon tested units working properly now."

We serviced a

BEKO DRYER

Model 7185881600

Near Minneapolis, MN 55436

Nate

Job Details: 03/01/2024

"The drum was locked up, but when we arrived, the dryer was working properly. We took it apart enough to access the internals to look for anything out of the ordinary (or signs of a problem) but could not find any issues. Belt was good. Motor good. Nothing in blower wheel. Rollers good. Looks like motor possibly got overworked and stopped due to overheat."

We serviced a

BOSCH DISHWASHER

Model SHXM88Z75N/01

Near Saint Paul, MN 55116

Hyrum

Job Details: 03/01/2024

0511 Sealing006368670512 Nut10024356Leaking from zeolite container seal. Discovered seal nut was cracked. Need replacement parts. Ordered parts from marcone ; ordrd 1 10024356 (Seal) and 1 00636867 (Nut)

We serviced a

LG DISHWASHER

Model LSDT9908SS

Near Hopkins, MN 55305

Adam

Job Details: 03/01/2024

Customer is complaint noise during. Put unit in test mode found that the motor is extremely loud and weak. Will need new motor assembly ordered part and rescheduled.; ordrd 1 AGM30016301 (Motor)

We serviced a

LG DISHWASHER

Model LDP6810SS

Near Minneapolis, MN 55422

Nate

Job Details: 03/01/2024

Replaced bad case assembly and inlet hose. Parts abq76120501 and mej63424801. Dried up all the water that had leaked out from the hoses that were broken. Reinstalled dishwasher and ran it and no leaks now. Runs great. ; schdld next appmnt for 3/5 TUE !

We serviced a

ASKO++ DISHWASHER

Model DFI664.U

Near Eden Prairie, MN 55344

Adam

Job Details: 03/01/2024

Customers complaint is screen went completely black and was Unresponsive. They went out of town for a week and came back and now its working. Tested everything. Everythings working properly at this time was getting some moisture through the seal. Theres a service bulletin for this issue and you need to replace the seal and get the new UI board. Added a bluebook quote to file. Explained to customer diagnosis and that the office will give you a final quote to make sure parts are available and no price changes.; saved tckt

We serviced a

BEKO WALL OVEN++

Model WOS30100SS

Near White Bear Lake, MN 55110

Hyrum

Job Details: 03/01/2024

"Customer states that it is burning food and then the temperature is dropping and really inconsistent. Turn the machine on And placed my temperature sensor inside. Temperature of the oven was about a hundred degrees hotter than the oven display was showing. Oven got as hot as 483 degrees. Then cycled to 343, then to 402, then dropped again. Called beko tech support, spoke wit Ed, they stayed it's likely a runaway temp sensor. Ordered part from marcone. ; ordrd 1 263410054 (Temp sensor)"

We serviced a

LG DISHWASHER

Model LDFN3432T

Near Minneapolis, MN 55403

Nate

Job Details: 03/01/2024

"Leaking and giving AE error. Found some water in flood pan. Dried water out, found a bad valve. Quoted and ordered valve. ; ordrd 1 5221DD1001E (Water valve)"

We serviced a

LG WASHER

Model WM2277HS/01

Near Minneapolis, MN 55408

Nate

Job Details: 03/01/2024

"Has a bad bearing. Quoted for bearing/tub assembly. Ballpark of $1400. RJ please refund half of trip charge, approved by RM. I tried calling, knocking, etc to let him know but no answer, can someone try calling him to let him know we are refunding half of trip charge? ; saved tckt"

We serviced a

SAMSUNG REFRIGERATOR

Model RF217ACPN/XAA

Near Minneapolis, MN 55444

Phillip

Job Details: 03/01/2024

The fresh food was very cold but the freezer is not cold enough. All fans working. I checked the pressure and food the lows for was minus 10 psi. I checked for leaks and found none. The fridge was just under charged. I added refrigerant. It happened while I was charging it and the relay failed. ; states that autho needed

We serviced a

GE RANGE

Model JB655SK7SS

Near Sauk Rapids, MN 56379

Brandon

Job Details: 03/01/2024

"Returned with board installed. Plugged in, the left number on the display did not come on, unplugged checked the board and connections and found not issues. Plugged in again and it worked all the functions worked."

We serviced a

BEKO WALL OVEN++

Model WOS30100SS

Near White Bear Lake, MN 55110

Hyrum

Job Details: 03/01/2024

We serviced a

SPEED QUEEN DRYER

Model ADE6HRYS178TW01

Near Cottage Grove, MN 55016

Delton

Job Details: 03/01/2024

Drum runs as soon as it is plugged in and control will beep continually. Canceling cycling will not stop and touch panel is not responsive. Found that the relay is stuck on the board always supplying power to motor. I tapped the relay on the board and motor stopped and dryer resumed working correctly.Needs new control board. Ordering part and rescheduling.; ordrd 1 D518191 (Control board)

We serviced a

GE RANGE

Model JBS07 M1WW

Near Saint Paul, MN 55104

Delton

Job Details: 03/01/2024

"Front right coil would get stuck on high even when set at 3 or 4. Replaced infinite switch. Tested and is working correctly now.; saved tckt , states that autho needed"

We serviced a

AMANA DRYER

Model NGD4600YQ0

Near Blaine, MN 55434

Phillip

Job Details: 03/01/2024

The dryer takes long to dryer and shuts off early. I tested the air flow and found its poor. I disconnected the duct and its perfect. The duct vents under the desk. Someone needs to come out and clean it right. ; saved tckt

We serviced a

SAMSUNG WALL OVEN++

Model NV51K7770DS/AA

Near Blaine, MN 55449

Phillip

Job Details: 03/01/2024

While the oven is heating the display goes blank/dead and sometimes they have to reset power. No fault codes. I need the parts listed below. DE94-03894B control board DG94-01617A-display board; states that autho needed

We serviced a

SPEED QUEEN WASHER

Model AWN632SP116TW02

Near Woodbury, MN 55129

Delton

Job Details: 03/01/2024

"Washer was full of water and unplugged when I got here. Customer said that it was stuck on soak option and wouldnt advance even after she canceled cycle and unplugged washer.I plugged in washer and pushed and held cancel cycle button and started spin cycle. It ran and drained out the water. I checked diagnostics and all functions are working. I ran cycle that customer normally uses and the washer fills, agitates, drains and spins. Washer is working good as im here.Customer will use as normal and call back if there is further issues.; saved tckt"

We serviced a

WHIRLPOOL RANGE

Model FFGF3047LSF

Near Minneapolis, MN 55428

Nate

Job Details: 02/29/2024

"Complaint is that it doesnt get hot enough. Ran for 20 minutes, bake and broil work. Averaged 375 when set at 350. Recommended getting new thermometer."

We serviced a

SAMSUNG RANGE

Model NX58K3310SS/AA

Near Plymouth, MN 55441

Nate

Job Details: 02/29/2024

Takes a long time to heat. Found a bad bake igniter. Replaced igniter. Heats great now.

We serviced a

FRIGIDAIRE RANGE

Model FFGF3047LSF

Near Minneapolis, MN 55412

Nate

Job Details: 02/29/2024

Takes a long time to heat. Found a bad bake igniter. Replaced igniter. Heats great now.

We serviced a

LG DRYER

Model NOTAVAILABLE

Near Rosemount, MN 55068

Delton

Job Details: 02/29/2024

"Found that the front rollers are worn out and shaking loudly. Also no heat du e to blower wheel bing full of lint. Customer approved estimate to replace front roller kit. Cleaned out dryer and replaced roller kit, tested and dryer is cycling heat normally and is running quiet. Dryer is working good

We serviced a

LG DRYER

Model DLG7301VE

Near Rockville, MN 56369

Brandon

Job Details: 02/29/2024

"Customer states the dryer is not drying.Cycled and tested. Cleaned out the inside of the dryer. Tested and found power going to the igniter the igniter was not coming on, quoted the customer a new igniter, customer approved, installed cycled and tested the igniter is coming on, the dryer is now heating like it should."

We serviced a

KENMORE REFRIGERATOR

Model 79575043610

Near Excelsior, MN 55331

Adam

Job Details: 02/29/2024

Installed new icemaker from last diagnosis once installed tested made sure it wasnt leaking. Everythings working properly.